Atlantic Ultraviolet Sanidyne 40-0674C Pengoperasian & Pemeliharaan Instalasi - Halaman 11
Jelajahi secara online atau unduh pdf Pengoperasian & Pemeliharaan Instalasi untuk Aksesori Atlantic Ultraviolet Sanidyne 40-0674C. Atlantic Ultraviolet Sanidyne 40-0674C 20 halaman.
s
P
r
aniDyne
rime
®
The Sanidyne
Prime Remote has two methods of controlling the unit; the Keypad Controller (Shown in Figure 2) and the
®
Hand-held Remote Controller (Shown in Figure 3). These two controls mirror each other; treatment times entered into Keypad
Controller will appear on the Hand-held Remote Controller and vice versa.
u
K
sing tHe
eyPaD
1.
Setting Treatment Time on the Keypad is done using the HOURS and MINUTES buttons which are located on the top of
the unit. (See Figure 1 for location) Selecting the up or down facing arrows located on the keypad in line with the HOURS
or MINUTES button will either increase or decrease the hours or minutes. The hours can be set between 0 and 24, and
the minutes can be set from 1 to 59. (Example of one hour and five minutes would appear as 01:05 on the Treatment Time
Display). Since the Keypad Controller will no longer be viewable once the treatment time begins, it is recommended that the
Hand-held Remote Controller be fully charged and powered before this time and be in possession of the operator at all times.
2. Determining the proper treatment times for your specific location can be done by using the "Recommended Treatment Time
for Room Size" chart (Figure 4 on Page 13).
3. Once the choice of time has been displayed on the Keypad controller, select the START/STOP button to begin and leave the
Operation Area immediately. Make sure that the Hand-held Remote Controller is kept in possession of the operator during the
Treatment Time.
Once you select the START / STOP button an audible exit alarm will begin to sound and the Sanidyne
Remote will begin counting down from 1:30 seconds to allow all inhabitants to leave the area before the UV treatment
begins. Additionally, the word "PrEP" will begin flashing on the Keypad and the Occupancy Sensors located on the
top of the unit (Shown on Figure 1) will begin to operate at this time, providing an additional safety area around the
unit. As an additional safety feature, if the sensors detect movement close to the Sanidyne
less than 30 seconds remain on the countdown time, the Sanidyne
seconds more to leave the Operation Area.
Occupancy Sensors do not protect the entire Operation Area of the Sanidyne
circumstances should this sanitizer be permitted to operate with humans, plants, or animals present in the Operation Area.
4. Outside the Operation Area the Treatment Time can be viewed on the Hand-held Remote Controller. Once the treatment time
has expired the unit will turn off the STER-L-RAY
The word "donE" will begin flashing on the Keypad Controller on the top of the unit.
u
H
-
sing tHe
anD
HelD
The Hand-held Remote Controller provides further detailed information on the Sanidyne
recommended to review the Hand-held Remote Controller Overview section of this manual to become familiar with the display
which is shown in Figure 3.
The Hand-held Remote Controller can operate the Sanidyne
imperative that the operator make a visual inspection of the Operation Area to ensure it is clear of all humans, plants, or
animals before proceeding.
1. Setting Treatment Time on the Hand-held Remote Controller is done by holding a finger on the display face, directly on the
words Treatment Time until the screen changes to a scroll bar. Next scroll the numbers up or down, characters on the left are
hours, characters on the right are minutes. Positioning the desired treatment time in the center row. (Example of one hour and
five minutes would appear as 01:05 on the Treatment Time Display) When times are positioned correctly, select DONE on the
bottom of the scroll bar to input your Treatment Time choice.
2.
Determining the proper treatment times for your specific location can be done by using the "Recommended Treatment Time
for Room Size" chart (Figure 4 on Page 13).
3.
Once the choice of time has been displayed on the Hand-held Remote Controller, select the start button to begin and leave the
Operation Area immediately. Make sure that the Hand-held Remote Controller is kept in possession of the operator during the
Treatment Time. (Remote Controller Instructions Continued on Page 12)
o
emote
Peration
C
s
ontroller to
et
r
C
emote
ontroller to
t
t
reatment
imes
Prime Remote will automatically reset giving 30
®
Germicidal Ultraviolet Lamps and it is now safe to return to the area.
®
s
t
et
reatment
Prime
®
Prime Remote when
®
Prime Remote. Under no
®
t
imes
Prime Remote. Therefore it is
®
Prime Remote remotely, thus it is
®
11