Anova rcp6 Petunjuk Perakitan dan Penggunaan - Halaman 2
Jelajahi secara online atau unduh pdf Petunjuk Perakitan dan Penggunaan untuk Perabotan Dalam Ruangan Anova rcp6. Anova rcp6 4 halaman. Recycled plastic picnic table
Halaman Cetak5. Install a Support Bar along the inside edge of one of the Angle Brace Mounts.
Note: The Support Bar has small chamfers on the upper corners. Install
the Support Bar so the chamfers are away from the Table Top
Surface.
Place the Support Bar on the Table Top first, then slide it against the
Angle Brace Mount. Make sure the Support Bar maintains contact
with the Table Top. Drive the Phillips Screws through the holes in
the Support Bar, into the Angle Brace Mount.
Install the remaining Support Bar against the other Angle Brace
Mount in the same manner.
6. Set the Table Top aside on a padded surface.
7. Locate a Left Leg and a Right Leg and insert Carriage Bolts through the two holes closest to the thick ends. Insert the Bolts from
the single-layer side toward the double-layer side. Use the Hammer to seat the Bolts. Lay the Legs out in an "A" shape with the
Thick Leg Ends facing up.
Position a Seat Support over the Legs and Bolts with the bottom of the Support contacting the thicker portion of the Leg end.
Place a Flat Washer, Split Washer and
Hex Nut on the end of each Carriage Bolt.
NOTE: Installing the Carriage Bolt in this
direction reduces the risk of being
scratched by the bolt end while using or
moving the assembled Table.
Leave the hardware finger tight so
adjustments can be made while
attaching the Seat Stiffeners (Step 9).
Repeat this step for the other pair of
Legs and Seat Support.
8. Locate the Leg Mounts. Place one of them at the top of each set of Legs. Insert Carriage Bolts through the Mounting Holes near
the top of each Leg and through the matching holes in the Leg Mounts. Use the Hammer to seat the Carriage Bolt and expose
the threads. Place a Flat Washer, Split Washer and Hex Nut on the end of each Carriage Bolt. Leave the hardware finger tight.
NOTE: Installing the Carriage Bolt in this
direction reduces the risk of being scratched
by the bolt end while using or moving the
assembled Table.
9. Install the Leg Mount Brace along the lower
edge of the Leg Mount. The face of the
Brace with 6 holes should be installed on
the wide face of the Leg Mount. Use nine
#10 x 3/4" Phillips Screws to fasten the
brace. Repeat this step for the other Leg
Mount Brace on the second Leg Mount
Assembly.
10. Use the Torx T25 driver to start two T25 x 3.0" Torx Screws into the pilot holes at the end of one of the Seat Supports in the Leg
Assembly. Stop as the points of the Screws emerge from the other side of the Seat Support.
Hold the Leg Assembly upright and position one of the Seat Stiffeners so the pilot holes in the end of the Stiffener line up with the
emerging Screw points of the Seat Support. Use the Torx T25 Driver to drive the T25 x 3.0" Torx Screws into the Seat Stiffener.
Repeat this step to attach
the other Seat Stiffener to
the other side of the Leg
Assembly.
Attach the other Leg
Assembly to the other end
of the Seat Stiffeners in the
same manner.
T25 x 3" Torx Screws
Hex Nut
Split Washer
Flat Washer
Thick Leg End
Phillips Screws
Phillips Screws
Seat Stiffener
Seat Support
T25 x 3" Torx Screws
Support Bar
Hex Nut
Split Washer
Flat Washer
Angle Brace Mount
Phillips Screws
Seat Support
Hex Nut
Leg Mount
Split Washer
Flat Washer
Carriage Bolts
Leg Mount Brace
T25 x 3" Torx Screws
Seat Support
T25 x 3" Torx Screws
Hex Nut
Split Washer
Flat Washer
Carriage Bolts
2 of 4