DSC Envoy NT9010 Panduan Pengguna - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Sistem Keamanan DSC Envoy NT9010. DSC Envoy NT9010 20 halaman. Demo stand
Juga untuk DSC Envoy NT9010: Petunjuk Instalasi (4 halaman)

Halaman Cetak

Entry/exit

Your installer will program the doors you usually use to enter or exit the premises

doors

as the entry/exit doors. These doors are programmed with entry and exit times so

that you can turn the system on and off without causing a false alarm.

Exit time

A timer programmed by your installer. It starts when you turn on your system to

allow you a period of time to leave the premises. At the end of the exit time, the

system will be on.

Local

If your NT9010 system is connected to your home/office telephone line, you may

telephone

be able to use a telephone key to access the system.

Master code

The master code is, a 4- or 6- digit access code, is used to set system options, to

turn the system on and off, and to program other access codes.

Remote

If your NT9010 system is connected to your home/office telephone line, you may

telephone

be able to use an off-premise (remote) telephone to access the system.

Stay mode

Turning on the system so that only the perimeter zones (see zone definitions,

below) are on. (Use when one or more people will stay on the premises.)

Trouble

The NT9010 controller continuously checks the system for problems. If the control-

ler finds a problem (trouble), it will indicate this at the keypad. See Checking

Trouble Conditions on page 19 for a list of possible trouble conditions, and how

they are displayed or announced.

Zone

A limited area of the premises monitored by a detector (smoke detector, door/win-

dow contact, motion detector, glassbreak detector, etc.).

Perimeter zone: A zone that detects intrusion from outside the premises (e.g.,

door contact on an outside door, glassbreak detector).

Interior zone: A zone that detects intruders who have already entered (e.g., a

motion detector).

Fire zone: A zone that has a heat or smoke detector.

Microphone

You can use the microphone to record a voice

memo on the NT9010. To record a memo, press

the Record button, then talk into the microphone.

When you are finished recording, press

. To

play the memo, press the Playback button.

If central station talk/listen-in is enabled on your

system, the microphone will also allow you to

talk to your central station operator.

Siren

The NT9010 uses the siren to warn you about

fire and burglary alarms.

Speaker

The NT9010 uses the speaker to broadcast sys-

tem announcements, instructions, recorded

memos, and alarms.

Status Lights

The NT9010's "Ready", "Armed" and "System"

status lights provide instant visual feedback on

the status of your security system.

Green "Ready" Light

If the Ready light is ON, the system is ready to be

turned on. You will not be able to turn the sys-

tem on unless the Ready light is ON (see Turn-

ing On Your System on page 9).

If the Ready light is flashing, someone has

recorded a voice memo on the NT9010. Press

the Playback button to listen to the recording.

Red "Armed" Light

If the Armed light is ON, the system has been

turned on successfully.

Yellow "System" Light

If the System light is ON, one or more of these

conditions could be present on the system:

System Troubles (See Checking Trouble Condi-

tions on page 19).

Alarms in Memory (See Turning Off Your Sys-

tem on page 10).

N T90 10 C o nt rol le r Fe atu re s

Zones Bypassed (turned off) (See Turning Off

Part of Your System (Bypassing Zones) on

page 18).

Programming. The System light will flash when

you are programming access codes, or perform-

ing other programming functions.

Emergency Keys:

In an emergency, you can use these keys to

instantly contact your central station:

Press both

* keys for two seconds to send a

Fire message.

Press both

* keys for two seconds to send

an Auxiliary message.

Press both

** keys for two seconds to send a

Medical message.

Press both

* keys for two seconds to send a

Panic message.

IMPORTANT NOTE: *The Fire, Auxiliary or

Medical, and Panic keys will NOT function

unless programmed by the installer. If these

keys are in service and the installer has

enabled audible feedback, holding down

both keys for two seconds will cause the

keypad sounder to beep indicating that the

input has been accepted and sent.

**The Medical keys are available only on units

intended to be monitored for medical applications.

Number Pad

Use the number pad to enter your access code

and system commands. To select a function

press

. To exit a function press

Function Buttons

If your installer has enabled them, you can use

the function buttons to access the stay, away,

door chime, quick exit, status, volume control,

memo record, and memo playback features. To

use a feature, press and hold one of the buttons

for two seconds. Refer to this Guide for more

information on these features.