Anywire AnyWireASLINK BS-K5217-M30-1K Panduan Produk - Halaman 8

Jelajahi secara online atau unduh pdf Panduan Produk untuk Aksesori Anywire AnyWireASLINK BS-K5217-M30-1K. Anywire AnyWireASLINK BS-K5217-M30-1K 9 halaman. Aslink sensor

Halaman Cetak

[Troubleshooting]

If the following statuses of the LEDs are indicated on the

ASLINKSENSOR, take the following actions.

LINK

ALM

○

Unlit

●

○

Lit

Unlit

◎

○

Unlit

Flashing

(alternates

with a 0.5 sec

interval)

－

◎

Flashing

(Lit for 0.2

sec, unlit for

1.0 sec)

◎

－

●

Flashing

Lit

◎

－

Flashing

(alternates

with a 0.1 sec

interval)

If the following error is indicated on the Address Writer, take the

following action.

Display

Cause

The parameter setting is

【E-0303】

incorrect.

Should any of the following apply, take the following actions.

Symptom

Detection cannot

- Is the metal piece to be detected in an appropriate position?

be made

Adjust the position of metal piece so that it will be in an

→

appropriate range from the detection face of

ASLINKSENSOR.

- Is the wiring correct?

Ensure that the ASLINKSENSOR transmission line is

→

connected to the AnyWireASLINK system transmission line

(DP, DN) properly.

- Is there a power supply with a capacity appropriate for the

AnyWireASLINK master and slave units and turned ON?

Check the power supply.

→

- Has teaching been performed?

Perform teaching using the workpiece to be detected in the

→

operation.

- Is the sensor used in the speci ed detection range?

Use it within its rating.

→

Setting cannot be

- Is the wiring correct?

made with the

Check the connection of ASLINKSENSOR transmission

→

Address Writer

line once more.

- Is the power supplied to the AnyWireASLINK system?

Check the power supply.

→

- Are the parameters set correctly?

Check the parameters and correct them accordingly.

→

[Parameter and Setting Items]

Parameters

Variable

0-100%

The threshold of sensing level to

【01.】

determine if a detection is made

Threshold

0-100%

The change in the sensing level required

【02.】

Hysteresis

for the detection status to change from

ON to OFF

0-100%

The upper limit for alarm determination

【03.】

Alarm Hi

0-100%

The lower limit for alarm determination

【04.】

Alarm Lo

3-255

The monitoring time for alarm

【05.】

determination (1=100ms)

Alarm

monitoring time

【06.】

Normally open

NO/NC

Normally closed

【07.】

OFF

Alarm feature

【10.】

Delay timer disabled

Delay timer

ON delay timer

ON/OFF

OFF delay timer

ON/OFF delay timer

0-255

The delay for the delay timers

【11.】

(1=100ms)

Delay

Cause

Remedy

- The ASLINKSENSOR

- Check if there is a disconnection

is not connected to

between the ASLINKSENSOR and

the AnyWireASLINK

AnyWireASLINK system and, if there

system.

was a disconnection, restore the

connection.

- The AnyWireASLINK

system is not turned

- Check the power supply of

on.

AnyWireASLINK system and turn ON

the power.

- Connected directly to

- Reconnect the power to the

the 24-0V power supply.

AnyWireASLINK system.

- The address of

- Assign an address other than 255.

ASLINKSENSOR

remains as "255"

(factory setting).

- The address of

- Look for a unit that has the same error

ASLINKSENSOR is

and assign an address different from

duplicated.

the address of that unit.

- The transmission

- Reduce the number of units connected

signal level is

to the same AnyWireASLINK system.

detected low.

- Reduce the length of transmission line

between ASLINKSENSOR and the

master unit.

- The sensing level is

- Check the condition of

low.

ASLINKSENSOR, adjust its position

and clean the detection face.

- Teaching has not

- Perform the teaching operation again.

been performed

properly.

Remedy

Check the parameters and correct

them accordingly.

Remedy

Description

[Speciﬁcations]

■General Speci cations

Ambient temperature/humidity use

Ambient temperature/humidity storage

Atmosphere use

Altitude use*

Pollution level*

*1 Do not use or store AnyWireASLINK devices in an environment where the pressure exceeds

the atmospheric pressure at an altitude of 0 meters. Doing so may result in malfunction.

*2 "Pollution level" is an index that indicates the degree of occurrence of conductive substances

in the environment where the device is used.

Pollution level 2 means the occurrence of only pollution by non-conductive substances.

In such an environment, however, electrical conduction could occur due to accidental condensation.

■Transmission Speci cations

Service power supply

voltage

Transmission method

Synchronization method

Transmission procedure

Connection mode

Number of connection

points

Number of units that can

be connected

RAS features

■Individual Speci cations

Occupied number of points

Current consumption

Detection target *

Standard detection substance

Detection distance

(at the ambient temperature of 23°C)

Stable detection distance

Hysteresis

Response time *

In uence of temperature

In uence of voltage

Protection class

Weight (Main unit, cable)

Weight (Nut)

3 The detection distance varies depending on the material.

4 The time from detecting the ON or OFF condition until the transmission signal is sent.

This time plus two transmission cycles will be the transmission delay.

Avoid using the device with splashes of water, oil or chemicals on it or in an

atmosphere causing condensation as those fluids may be recognized as

detection targets and leading to erroneous detections.

Factory

The device is especially sensitive to dielectrics and can be influenced by

setting

even a tiny drop of water.

M18: 5

M30: 6

If the device is to be mounted in a metal body, ensure the distances listed in

the table below.

Also ensure the distances shown on this table for installations in materials

other than metals (such as resin) could have an influence on the detection.

M18: 6

M30: 7

5 If the metal body is not grounded, the operation may be unstable. Always ground it.

BS-K5217-M18-1K

BS-K5217-M30-1K

-BSK5217M**1K 8/9-

-10 – 60°C, 10 – 90%RH No condensation

-25 – 75°C, 10 – 90%RH No condensation

No corrosive gas

0 – 2000m

2 or less

24V DC +15% to -10% (21.6 to 27.6V DC) with a ripple of

0.5Vp-p or less

DC power supply superimposed total frame/cyclic method

Frame/bit synchronization method

Dedicated protocol

Bus type (Multi-drop method, T-branch method,

Tree branch method)

512 max. (IN: 256, OUT: 256)

Up to 128 units

Detection of transmission line disconnection, detection of

transmission line short circuit, detection of transmission power

drop, detection of duplicated/unregistered ID

1 input point

Supplied by the AnyWireASLINK transmission signal (DP, DN)

M18: 7.5mA

Conductors/dielectrics

A grounded metal piece of 50 × 50 × 1mm

M18: 8mm（max.）

M18: 0 – 6.4mm

Depends on the parameter setting

10ms max.

The detection distance at 23°C

M18: Within ±20%

Within ±1% of detection distance in the range of 27.6 to 21.6V

power supply voltage for the AnyWireASLINK master unit.

IP67

M18: Approx. 38g

M18: Approx. 2g

φd

Metal body

M30: 7.6mA

M30: 15mm（max.）

M30: 0 – 12mm

M30: Within ±20%

M30: Approx. 64g

M30: Approx. 3g

(Unit: mm)