3onedata IAP3600S-225-2GT-PDP12 48 Panduan Instalasi Cepat - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Instalasi Cepat untuk Titik Akses Nirkabel 3onedata IAP3600S-225-2GT-PDP12 48. 3onedata IAP3600S-225-2GT-PDP12 48 4 halaman. Industrial outdoor dual-band wi-fi6 wireless ap

Halaman Cetak
Step 5
Install the device on the wall and tighten the screw.
Installation ends.
【Wall-mounted Device Disassembling】
Step 1
Power off the device.
Step 2
Hold the device steadily and screw out the screw in
the wall.
Step 3
Take out the device, disassembling ends.
Notice Before Powering on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
then plug the power supply plug contact and power on.
Power OFF operation: First, remove the power plug,
then remove the wiring section of terminal block. Please
pay attention to the above operation sequence.
【Power Supply Connection】
PoE power supply
The WAN port of this device supports 48VDC PoE power
receiving, which conforms to IEEE802.3af/at standard.
12~48VDC power supply
This device provides 1 DC power input which is
3-pin
5.08mm
pitch
waterproof plug, the power supply supports
non-polarity. Power supply range: 12 ～ 48VDC. The pin
definitions of power supply are shown as follows:
PIN
Description
【Reset Button Setting】
The device provides 1 RESET button that can be used
to reboot the device and restore factory defaults. Press
the RESET button for 1~2s and release it, and the device will
restart automatically; Press and hold the RESET button for 5s
and release it, and the device will automatically restore the
factory defaults.
【Checking LED Indicator】
The device provides LED indicators to monitor its operating
status, which has simplified the overall troubleshooting
process. The function of each LED is described in the table
below:
LED
RUN
2.4G
5G
WAN
terminal
block
with
LAN
1
2
3
V-
FG
V+
Indicate
Description
The device is powering on or the
ON
device is abnormal.
Blinking
The device is running normally
The device is powered off or the
OFF
device is abnormal.
ON
2.4G wireless signal is on.
2.4G
wireless
Blinking
transmitting data
2.4G wireless signal is running
OFF
abnormally or turned off
ON
5G wireless signal is on.
5G wireless signal is transmitting
Blinking
data
5G wireless signal is running
OFF
abnormally or turned off
The
Ethernet
interface
ON
established an active network
connection
/
The Ethernet interface is in a
Blinking
network activity state.
The Ethernet interface has not
OFF
established an active network
LED
Indicate
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access the device via device LAN port. The
way of logging in to device's configuration interface via IE
browser is shown as below:
Step 1
Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed
signal
is
Step 2
Enter device's IP address in the address bar of the
computer browser.
Step 3
Enter device's username and password in the login
window as shown below.
has
Step 4
Click "Login" button to login to the WEB interface of
Description
connection.
The
indicators
are
all
off,
indicating that no bridge has been
established.
One indicator is on. It means
2.4G/5G signal at the opposite
end is weak
Two indicators are on. It means
2.4G/5G signal at the opposite
end is normal
All indicators are on. It means
2.4G/5G signal at the opposite
end is strong