ADEMCO Vista 4120 Panduan Petunjuk Instalasi - Halaman 15

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Sistem Keamanan ADEMCO Vista 4120. ADEMCO Vista 4120 18 halaman.

Halaman Cetak

TESTING THE SYSTEM

After installation is completed. the Security System should be

carefullv tested.

With the System in the disarmed state, check that all zones

are intact. lf NOT READY is displayed, press the ['I key to

display the faulted zone(s). Restore faulted zone(s) if

necessary, so that READY is displayed. Fault and restore

every sensor indiiidually to assure that it is being monitored

by the system.

Enter the wcurlty

code and press the TEST key. The

external sounder (ff used) shoukf sound for 3 seconds and

then turn off and a test report should be transmitted (if

programmed) to the Central Station. lf the badtup hattey is

discharged or missing, the external sounder will not turn on

and a LOW BATTERY report will be transmitted instead of a

TEST report.

A message will he sent to the central statbn during the folbwing

test. Notify the central station that a test will be in progress.

Arm the system and fautt one or more zones. Silence alarm

sounder(s) each time by entering the code and pressing

OFF. Check Entry/Exit delay zones.

Check the keypad-initiated alarms by pressing the Panic

key pairs-[1 and 18) and/or p] and [8& If the system has

been programmed for audible emergency, the console will

emil a bud, steady alarm sound, and AlARM and 99 will be

diiyed

for 11 and [a (if p] and [rr) are pressed, 96 will

be displayed). Silence the atarm hy entering wcurlty code

end pressing OFF.

II the system has been programmed for silent em-ergency.

there will be no audible alarms or displays, but a report will

be sent to the central station.

Notify the central station that all tests are finished, and

verify results with them.

NOM:

ffthabattarystandbycapackyisexceadedduringanAC

power failwe. tha 4120 will automatically shut itself off so

that lt can retain 6s armed state (OFF, AWAY, STAY,

etc.). When AC power is restored, the 4120 will assume

its armed status prior to the AC power interruption.

TO THE INSTALLER

Rag&r mabtenanoa and lnsp&in

(at feast annually) by the

instafler and frequent tasting by the usar am vital to continuous

satisfsctory operation of any alarm system.

The installer should assume the responsibility of developing

snd offering a regular maintenance program to the user as well

as acquainting the user with the proper operation and

limitations of the alarm system and its component parts.

Recommendations must be included for a specific program of

frequent testing (at least weakly) to insure the system's proper

operatbn at all times.

SPECIFICATIONS

4120

SECURI'IY CONTROL

1. PhysIcal:

12-Vl'(318 mm) W.

14-12 (388 mm) Ii,

3' (76 mm) D

2. Ebctrfcal

VOLTAGE INPUT: 16.8VAC (from plug-in 26VA transfor-

mer, Adema, No. 132fm2). ln Canadian instal-

latbns. No. 1321 CN must be used.

RECHARGEABLE BACK-UP BATTERY: 12VDC. 4AH

(Gel or starved lead-acid type)

ALARM ST)UNfER: x)-13.8V. 2.8 Amp output (360 mA

max. on alarm for a UL instakatiin).

OUTPUT: Can drive 12V motor driven hells (100 mA

each) - AMSECC MSB16G or ABE1 031. Do not

use solenoid operated hells.

Can driie one 7tI2 or two 702 (series connected)

self-contained 29-watt sirens. Do not connect two

702s in parallel.

AUXIUARY POWER OUT-PUT:X)&13.8V DC, XI0 mA

max. for non-UL instalfati~. 400 mA max. for UL

installations.

STANDBY TIME: 4 HRS. with Auxiliary bad d 5oomA'

'Using 4 AH Battery

3. Communlcatkn:

FORMATS SUPPORTED:

Ademco Bxpresa, '10 char-acterslsec, DTMF (Touoh-

lone) Data Tones, 14M)I 2300 Hz ACK, 1400 Hz

KISSOFF.

Ademoo Low Speed, 10 pulseslsec, 1900 Hz Data

Tone, 1400 Hz ACW KISS-OFF.

RADIONICS. 20 pulses/ sec. 1800 Hz Data Tone, 2300

Hz ACKMISSDFF reports O-8, B-F).

Line Seize: Double Pole

Ringer Equivalence: 0.78

FCC Registration No.: AC 398U-68192-AL-E.

4127 REMOTE CONSOLE

1. Physfcal:

6-~(l43mm) W

44lrtQMmm) H

2. Elactrlcal:

7&= (22mm)D

Voltage Input: 12V DC

Current Drain: 20 mA

3. Interface Wlrlng:

RED: 12V DC input (+) aux pwr

GREEN: Data In

YELLOW: Data Out

BLACK: Ground

5330 REMOTE CONSOLE

1. Phyalcsl: 7-314yf43mm)W

67116'~%tnn)H

1 114' (32nxn)D

2 Ebctrlcal:

Voltage Input: 12V DC

Current Drain: 106 mA

3. lntertace Wlrlng:

RED: 12V DC input (+) aux pwr

GREEN: Data In

YELLOW Data Gut

BLACK: Ground

4137 REMOTE CONSOLE

1. physlcsl:

8-X. Ql3mm)W

4314' (12mm) H,

2. Electrkal:

l-lfia

(28mm)D

Voltage Input: 12V DC

Current Drain: 60 mA

3. Interface Wlrlng:

RED: 12V DC input (+) aux pwr

BLUE: Not Used

GREEN: Data ln

YELLOW: Data Out

BLACK: Ground