DBI SALA flexiguard 8560026 Panduan Petunjuk Instalasi - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Rak dan Dudukan DBI SALA flexiguard 8560026. DBI SALA flexiguard 8560026 8 halaman. Concrete mounted jib base

Halaman Cetak

WARNING: This product is part of a fall arrest or rescue system. These instructions must be provided to all

users and rescuers using this equipment. The user must read and understand these instructions before using

this equipment. The user must follow the manufacturer's instructions for each component of the system.

Manufacturer's instructions must be followed for proper use and maintenance of this equipment. Alterations or

misuse of this equipment, or failure to follow instructions, may result in serious injury or death.

IMPORTANT: If you have questions on the use, care, or suitability of this equipment for your application,

contact Capital Safety.

IMPORTANT: Before using this equipment, record the product identification information from the ID label into

the inspection and maintenance log of this manual.

IMPORTANT: Systems are designed to be used with Jib Systems manufactured by Capital Safety only.

OSHA Models

All connecting systems, (self retracting lifelines, winches and

energy absorbing lanyards) used with the Jib Mast and Base

system shall limit the average arresting forces to 4 kN (900

lbf).

IMPORTANT

System is only rated for one user.

8530483

8530564

General Construction

Structural Material

Finish

Hitch Pin Material

Hitch Pin Finish

Training: It is the responsibility of users of this equipment to understand these instructions and be trained

in correct installation, use, and maintenance of this equipment. Users must be aware of the consequences

of improper installation or use of this equipment. This instruction manual is not a substitute for a training

program. Training must be provided on a periodic basis to ensure user proficiency.

Description: The Concrete Mounted Jib Base (Figure 1) is a anchor point for overhead applications. The Concrete

Mounted Jib Base is designed for use with a vertical mast being inserted into a concrete mounted base.

Purpose: The Concrete Mounted Jib Base is designed for use as a component of a Personal Fall Arrest System

(PFAS). PFASs are used where free fall is possible before the fall is arrested and typically include: a Self

Retracting Lifeline (EN 360) or Energy Absorbing Lanyard (EN 355); connector (EN 362) to attach to the

anchor; and a Full Body Harness (EN 361).

INSTALLATION:

Step-1: Mark anchor holes to be drilled per Figure 2 -

• Drill 129mm (Ø5.06") hole to a depth of 578mm (22.75") into the existing concrete. (See Figure 2 -

Model

8530483

8560026

•

Remove debris from hole and inject epoxy into hole per manufacturer instructions. (See Figure 2 -

NOTE: Ensure that no epoxy ingresses into anchor opening during install. Capital Safety recommends using

Rock River® All Weather 400 Epoxy, (Part# 0269002, 9.3 oz tube) or equivalent to anchor base.

• After the Concrete Anchors have cured over the appropriate time as specified by epoxy manufacturer,

continue on to Step 2.

Step - 2: Fastening the Mounted Jib Base:

• Make sure the Core Holes are free of any debris before inserting the Jib Base. (See Figure 3.)

• Fasten the Jib Base to the existing concrete by tightening the concrete anchor bolts to their

recommended torque.

SPECIFICATIONS:

Welded Steel

A36 Steel

Zinc Plate per ASTM B633, Type 2

A36 Steel

Zinc Plate

Mounting Hardware Minimum Moment Load

39,047 N*m (345,600 in*lbs)

29,286 N*m (259,200 in*lbs)

CE Models

All connecting systems, (self retracting lifelines, winches and

energy absorbing lanyards) used with the Jib Mast and Base

system shall limit the average arresting forces to 6 kN (1350

lbf).

IMPORTANT

System is only rated for one user.

layout.

8560026

Minimum Vertical Load

16 kN (3,600 lbs)

12 kN (2,700 lbs)