ALLNIC AUDIO H-3000 Panduan Pemilik - Halaman 7

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Penguat ALLNIC AUDIO H-3000. ALLNIC AUDIO H-3000 12 halaman. Phono stage
Juga untuk ALLNIC AUDIO H-3000: Panduan Pemilik (14 halaman)

Halaman Cetak

screw type connector. This connector is the ground

connection for a ground wire from a cartridge and/or

turntable.

When you are facing the front of the H‐3000, the two pairs of

MC connections are on the right/centre of the unit, with the

two MM connections immediately to their left on the other

side of the ground connection.

The H‐3000 has been designed and manufactured to work

most synergistically with Allnic Audio preamplifiers, pre‐

phono stages and equalization products.

OUTPUTS

The H‐3000 is equipped with one pair of unbalanced or

"single‐ended" (RCA) outputs and one pair of true balanced

(XLR) output connections. The left channel output

connections are labeled "left output" and are just to the left

of the DC Source Input. The right channel output connections

are labeled "right output" and are on the far left hand side of

the rear of the phono stage unit (See Figure 1). In each pair,

the balanced (XLR) connection is labeled "1", and the

unbalanced (RCA) connection is labeled "2".

Above each pair of outputs, comprised of one single‐

‐ended (RCA) connection and one balanced (XLR)

connection, is a switch for selecting either the balanced

or the single‐ended connector. The switches are labeled

"unbalanced output". Moving the unbalanced output

switches to the right (facing the rear of the unity) sets

the outputs to their respective unbalanced (RCA)

connector. Of course, the opposite position in each

case sets the switches for the balanced connectors. Be

sure to have both switches set for the connection you

are using. You may have both balanced and unbalanced

outputs connected at the same time without

introducing hum PROVIDED you have the output

switches set to unbalanced output.

Moving Coil (MC) Transformer Controls

On the top of each channel's MC transformer on the

centre rear of the chassis deck of the phono stage unit,

there is a rotating control. Turn the control knob to select

from four gain factors.

The "X#" scale corresponds to the factor that you will select

for the millivolt output of your selected MC cartridge. Each

position on the X# (factor) scale corresponds to an increase

in gain, indicated on the "+#dB scale. You should use

identical settings for both transformers to avoid channel

imbalance.

NOTE:

Please mute your H‐3000, and/or reduce your

preamplifier's volume control, during transformer gain

adjustments. Be aware if you are increasing gain, that you

may hit an uncomfortably loud volume level.

A NOTE ON PHASE

Phase issues generally will result in lack of bass and/or

focus of the stereo image. You may need to reverse

connections on your cartridge if you are having phase

issues. As is usual in these circumstances, some trial and

error experimentation may be required to find the correct

position. The process is simplified for you with the H‐3000,

as it has a phase control switch on the front panel of the

phono stage unit.

IMPEDANCE

In the Specifications at the end of this manual, you will

read that the moving coil (MC) input impedance for the H‐

3000 is up to 470 ohms. This value represents the internal

impedance of the cartridge itself, and is at the very

extreme of what would normally be expected for the

internal impedance of an MC cartridge. It would be

exceptionally unusual to find a cartridge with internal

impedance greater than that value.

INITIAL POWER‐ON

Once you have your H‐3000 in place and all connections have

been made to your turntable and preamplifier, you are ready to

turn on the power for your H‐3000. Before you power up the H‐

3000, though, be sure you have:

•

removed all the cushion materials between the tubes and

the protective parts of the chassis

•

selected the output connections that you want to use, single

ended (RCA) or balanced (XLR), on the two switches on the

back of the phono stage

•

turned the volume down or muted your preamplifier