ALLRIGHT LGL15144 Series Petunjuk Pengoperasian - Halaman 2

Jelajahi secara online atau unduh pdf Petunjuk Pengoperasian untuk Tangga ALLRIGHT LGL15144 Series. ALLRIGHT LGL15144 Series 2 halaman. Fiberglass multi-use ladder system 300 lbs duty rating

Halaman Cetak

General:

1. Do not force the hinges in or out using any tools. You may

cause permanent damage to the hinge mechanism.

2. If there is pressure on the hinge lock pins, they may not

open properly. Relieve the pressure by moving one half of

the ladder back and forth until the hinge locks move with

minimal force.

3. Make sure each Rock Lock is fully engaged into the

appropriate rung tube before climbing on the ladder. Failure

to do so may result in injury.

4. For your safety, set up your ladder so the rungs are always

level from front to back and from side to side.

5. Keep clothing and body parts out of all moving

mechanisms, including the Hinge Locks and Rock Locks to

avoid pinching.

6. Keep clothing and body parts away from rungs when

telescoping the outer ladder over the inner ladder.

7. Use caution when using the ladder around electricity.

Ensure that the ladder does not come in contact with

electrical circuits or currents.

8. The Conquest has an OSHA and ANSI Type IA duty rating

of 300 pounds.

9. Do not stand above the third rung from top.

10. Little Giant Ladder Systems assumes no liability for

damage or injury that may result from failing to follow all

instructions correctly.

11. Keep all ladder rungs, ladder feet, work platforms, and

other standing and gripping surfaces clean and free from

foreign materials.

12. Do not lean too far over the side of the ladder and keep

both feet on the rungs at all times; as a rule of thumb, keep

your navel between the rails.

13. Inspect feet for wear; replace them when necessary.

14. Read all labels on the ladder before use. A-Frame and

Staircase Ladder Safety Tips:

1. Ensure that the Hinge Locks and Rock Locks are securely

engaged before climbing your ladder.

2. Make each of your ladder's four feet are solidly planted

before climbing.

3. When using your ladder on a stair case, ensure that the

rungs are level and that each foot is on a solid, secure

surface.

Extension Ladder Safety Tips

1. Do not allow the full weight of the ladder to fall on the

hinges as the ladder folds from the extension to the A-frame

position.

2. Flared base must be placed at the bottom of the ladder in

the extension position.

OPERATING INSTRUCTIONS

File: ALC – LGL15144 – Operating Instructions – V15.1

3. When releasing the Rock Locks, make sure you support

the inner ladder assembly with one hand to prevent it from

sliding down rapidly. Failure to do so may result injury.

4. Use the proper angle for the extension ladder position.

The distance from the base of the ladder to the bottom of

the support wall should be one-fourth the working height of

the extension ladder (minimum distance between ladder

and support wall must be 3 feet).

5. Fully engage the Hinge Locks before use, failure to do so

may result in injury.

6. When using your Conquest as a tall extension ladder,

stake the feet to the ground and tie down the top for extra

security. Extend the ladder at least 3 feet above a supporting

roof or eve.

Scaffolding Safety Tips

1. Do not use outer or inner sections of the ladder as a

separate stepladder.

2. Be sure to set the two outer ladder assemblies with the

rungs facing out with the trestle brackets properly engaged.

3. When the scaffolding plank is above the third rung (three

feet high), it may be used as a work bench, but not as a

standing platform.

4. ANSI rules state that the scaffolding plank should not be

used as a standing platform at heights greater than three

times the minimum width of the base section.

5. The scaffolding system has a one-man, 250-pound rating.

6. Only one person should be on the scaffold plank at a time.

Work Platform Safety Tips

1. If you purchased a Work Platform for your Conquest, you

can use it as an additional tool tray or as a standing platform.

2. Do not use the Work Platform as a standing platform

above the third rung from the top, in either A-frame and

extension configurations.

3. Make certain the Work Platform is secure on the rung

before standing on it