Panasonic CT-2524L Manual - Halaman 12
Jelajahi secara online atau unduh pdf Manual untuk TV Panasonic CT-2524L. Panasonic CT-2524L 28 halaman.
Halaman Cetak
REMOTE CONTROL OPERATION
Programming
The Remote Control
The Universal
Remote Control can be programmed
to
operate
many
manufacturers'
components,
using the
component
function
buttons for VCR,
DVD, CABLE
or
DBS. Follow the procedures for programming your Remote
Control with or without a code for the component.
TV
TV (Panasonic
Only)
Panasonic Code
VCR
VCR (Preset)
Panasonic Code
DBS/OBL
DBS STB & CBL STB (Preset)
Panasonic DBS Code
DVD
DVD (Preset)
Panasonic Code
Note:
Determine
the manufacturer
of the component
and look
in the table for the code
(found on page
11).
Procedure
1.
Confirm
that the external
component
is plugged
in and
operating.
2.
Turn the component
off.
ACTION
3.
Press
and
together,
for
at
least
5
seconds.
After
5
seconds,
the
illuminated
mode
(component)
buttons
will
begin
to flash.
Release
the
ACTION
and POWER
buttons.
4.
Press
appropriate
component
button
on the
Remote
Control
VCR,
DVD,
CABLE
or
DBS.
The
component
button
will illuminate
steadily
and all others
will go out.
5.
Enter
the 3-digit
component
code
using
the
Remote
Control
numeric
keypad
(O ~ 9 buttons).
The component
button
will blink twice.
6.
Press
the
Remote
Control
to
test
the
component.
If
the
procedure
was
successful,
the
component
will turn on and the component
key will blink
twice and then go out.
Note:
If the
component
does
not
operate
with
the
Remote
Control,
repeat
steps
3 through
6 using
another
code
(some
brands
have
multiple
codes).
If an incorrect
code
is entered,
or ff the procedure
takes
longer
than
30
seconds,
the programming
will fail.
Programming
Without
A Code
This procedure
searches
all codes
and is called
the
"sequence method."
1.
Confirm
that the external
component
is plugged
in and
on.
2.
Turn the component
off.
ACTION
3.
Press
and
together,
for
at
least
5
seconds.
After
5
seconds,
the
illuminated
mode
(component)
buttons
will
begin
to flash.
Release
the
ACTION
and POWER
buttons.
4.
Press
the appropriate
component
button
on the Remote
Control.
The
component
button
will
illuminate
steadily
and all others
will go out.
5.
Press
the
button
to set the remote
control
into
the step and set mode.
6.
Point the remote
control
towards
the component.
Note:
8.
Note:
Press VOL
•
(the mode
key will blink three
times),
then
press
the
Remote
Control
button
to test
the
component.
Continue
this process
until the proper
code
is found.
If the procedure
was successful,
the component
will turn
on.
Each time you press
the VOL
•
button,
make
sure
that
the
component
key
blinks
twice
before
pressing
the
POWER
button.
ACTION
Once
the device
responds,
press
to store
the
code. The mode
(component)
button
will blink twice.
It may
take
many
attempts
before
the
correct
code
is found.
If you miss
a code,
press
41 VOL,
then press
the
button
to test the component.
Component
Codes
The Universal
Remote Control
is capable
of operating
many component
brands after entering
a code. Some
components
may not operate because the codes are not
available due to limited memory. The Universal
Remote
Control does not control all features found in each model.
III ii
i i
VCR
CABLE
DVD
IIII
IIII
IIII
DBS
i
IIII
:
10e