Shimano FD-M985-E2 Manual

Jelajahi secara online atau unduh pdf Manual untuk Aksesori Sepeda Shimano FD-M985-E2. Shimano FD-M985-E2 2 halaman.

Shimano FD-M985-E2 Manual
SI-5M80A-002-00
General Safety Information
WARNING
"Maintenance interval depends on the usage and riding circumstances. Clean regularly the chain
with an appropriate chaincleaner. Never use alkali based or acid based solvents such as rust
cleaners. If those solvent be used chain might break and cause serious injury."
• In order to obtain good gear shifting performance, this chain has a forward side and a reverse side, and the
sides are marked so that the chain will face the correct way when installed. The proper design performance
will be obtained when the chain is installed so that it faces the correct way. If it is installed so that it faces
the opposite way, the chain may come off and the bicycle may fall over and serious injury may occur as a
result.
• Use the reinforced connecting pin only for connecting the narrow type of chain.
• If connecting pins other than reinforced connecting pins
are used, or if a reinforced connecting pin or tool which
Chain
is not suitable for the type of chain is used, sufficient
connection force may not be obtained, which could
cause the chain to break or fall off.
10-speed super narrow
• If it is necessary to adjust the length of the chain due to
chain for
MTB
a change in the number of sprocket teeth, make the cut
at some other place than the place where the chain has
been joined using a reinforced connecting pin. The chain will be damaged if it is cut at a place
where it has been joined with a reinforced connecting pin.
• Be careful not to let the cuffs of your clothes get caught in the chain while riding, otherwise you
may fall off the bicycle.
• Check that the tension of the chain is correct and that the chain is not damaged. If the tension
is too weak or the chain is damaged, the chain should be replaced. If this is not done, the chain
may break and cause serious injury.
• The two left crank arm mounting bolts should be tightened alternately in stages rather than each bolt being fully tightened all at
once. Use a torque wrench to check that the final tightening torques are within the range of 12 - 14 N·m. Furthermore, after
riding approximately 100 km (60 miles), use a torque wrench to re-check the tightening torques. It is also important to
periodically check the tightening torques. If the tightening torques are too weak or if the mounting bolts are not tightened
alternately in stages, the left crank arm may come off and the bicycle may fall over, and serious injury may occur as a result.
• Check that there are no cracks in the crank arms before riding the bicycle. If there are any cracks, the crank arm may break and
you may fall off the bicycle.
• If the inner cover is not installed correctly, the axle may rust and become damaged, and the bicycle may fall over and serious
injury may occur as a result.
• Obtain and read the service instructions carefully prior to installing the parts. Loose, worn or damaged parts may cause the
bicycle to fall over and serious injury may occur as a result. We strongly recommend only using genuine Shimano replacement
parts.
• Obtain and read the service instructions carefully prior to installing the parts. If adjustments are not carried out correctly, the
chain may come off and this may cause you to fall off the bicycle which could result in serious injury.
• Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.
CAUTION
• If the chain is on the smallest or intermediate chainring, there is the danger of injury from the tips of the teeth on the largest
chainring.
Note
• In addition, if pedaling performance does not feel normal, check this once more.
• Before riding the bicycle, check that there is no play or looseness in the connection. Also, be sure to retighten the crank arms
and pedals at periodic intervals.
• If a squeaking noise is heard coming from the bottom bracket axle and the left crank arm connector, apply grease to the
connector and then tighten it to the specified torque.
• Use a neutral detergent to clean the crank arm and the bottom bracket. Using alkaline or acidic detergents may cause
discoloration.
• Do not wash the bottom bracket with high-pressure jets of water.
• If you feel any looseness in the bearings, the bottom bracket should be replaced.
• If gear shifting operations do not feel smooth, wash the derailleur and lubricate all moving parts.
• If the amount of looseness in the links is so great that adjustment is not possible, you should replace the derailleur.
• You should periodically wash the chainrings in a neutral detergent and then lubricate them again. In addition, cleaning the chain
with neutral detergent and lubricating it can be an effective way of extending the useful life of the
chainrings and the chain.
• If the chain keeps coming off the chainrings during use, replace the chainrings and the chain.
• When the chain is in the position shown in the illustration, the chain may contact the front chainrings
or front derailleur and generate noise. If the noise is a problem, shift the chain onto the next-larger
rear sprocket or the one after.
• For frames with suspension, the chain stay angle will vary depending on whether the bicycle is being
ridden or not being ridden. When the bicycle is not being ridden and the chain is positioned on the
largest/larger chainring and on the smallest sprocket, the chain guide outer plate of the front derailleur
may touch the chain.
• The cuffs of your clothing may get dirty from the chain while riding.
• Apply grease to the left and right adapters before installing them.
• For smooth operation, use the specified outer casing and the bottom bracket cable guide.
• The front derailleur is for double front chainwheels only. It cannot be used with triple front chainwheels, as
the shifting points will not match.
• When installing the top route type, choose a frame that has three outer casing holders as shown in the
illustration at right.
• Use an outer casing which still has some length to spare even when the handlebars are turned all the way to both sides.
Furthermore, check that the shifting lever does not touch the bicycle frame when the handlebars are turned all the way.
• A special grease is used for the gear shifting cable. Do not use DURA-ACE grease or other types of grease, otherwise they may
cause deterioration in gear shifting performance.
• Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly.
• Operation of the levers related to gear shifting should be made only when the front chainwheel is turning.
• If the brake fluid used in the oil disc brakes is of a type which tends to adhere to the plastic parts of the shifting lever, this may
cause the plastic parts to crack or become discolored. Therefore, you should make sure that the brake fluid does not adhere to
these plastic parts. The mineral oil which is used in SHIMANO disc brakes does not cause cracking or discoloration if it adheres
to plastic parts, but such parts should be cleaned with alcohol beforehand to prevent foreign particles from adhering.
• Do not disassemble the shifting lever unit, as this may damage it or cause mis-operation.
• Be sure to read the service instructions for the Rear Drive System in conjunction with these service instructions (SL-M980-I).
• Parts are not guaranteed against natural wear or deterioration resulting from normal use.
• For maximum performance we highly recommend Shimano lubricants and maintenance products
• For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a professional
bicycle dealer.
Technical Service Instructions
Front Drive System
In order to realize the best performance, we recommend that the following combination be used.
Series
Rapidfire (Shifting lever)
SL-M980-L / SL-M980-IL
Outer casing
OT-SP41 (SIS-SP41)
Front derailleur
FD-M985 / FD-M985-E / FD-M985-E2 / FD-M986 / FD-M986-D
Front chainwheel
FC-M980 / FC-M985
Chain
Bottom bracket cable guide
Specifications
Front Derailleur
Model number
Normal type
Top route type
Front chainwheel tooth difference
Front derailleur installation band diameter
Chainstay angle (
)
a
Applicable chain line
Reinforced
Chain tool
connecting pin
Chainwheel
Model number
with groove (3)
TL-CN32
TL-CN23
Chainwheel tooth combination
TL-CN27
with groove (2)
Bolt circle diameter
Crank arm length
Reinforced Connecting Pin
Chain line
Bottom bracket shell width
Thread dimensions
Link Pin
Link Pin
Applicable bottom bracket
Gear shifting operation
The INSTANT RELEASE mechanism makes fast releasing possible because cable tension is released immediately when a lever is
depressed.
This release lever is equipped with a 2-way release mechanism which allows release operations to be carried out by either pushing or
pulling the lever.
Both lever (A) and lever (B) always return to the initial position when they are released after shifting.
When operating one of the levers, always be sure to turn the crank arm at the same time.
To shift from the smaller chainring to the larger chainring
(Lever A)
When lever (A) is pressed once, there is a shift of one step from the
smaller chainring to the larger chainring.
Example:
From smaller chainring to larger chainring.
Lever (A) initial position
Front
chainrings
Installation of the Front Chainwheel
Follow the procedure in the figure.
Rear
sprockets
1, 2
Use the special tool TL-FC32/36 to install the right adapter
(counterclockwise thread) and the left adapter (clockwise
thread).
Outer casing holders
Tightening torque: 35 - 50 N·m {305 - 435 in. lbs.}
Note :
Spacers may be necessary depending on the bottom
bracket shell width. For details, refer to "Spacer
installation method".
3
Insert the right crank unit.
4
Set section A of the left crank into the axle of the right crank
unit where the groove is wide.
(A)
SI-5M80A-002
TL-FC16
XTR
Plate pin
CN-M980
Stopper plate
Push up
SM-SP17
FD-M985
FD-M985-E
FD-M985-E2
FD-M986
X
X
X
X
X
X
X
X
14, 12T
14, 12T
12T
14, 12T
S, M, L
S, M, L
66° - 69°
66° - 69°
66° - 69°
66° - 69°
46.8 mm
38T
38T
38T
48.8 mm
40-44T
40-44T
40T
40-44T
Installation band diameters:
S (28.6 mm), M (31.8 mm), L (34.9 mm)
FC-M980
FC-M985
When using the S, M size, use an
installation band with a diameter of 28.6
38-26T
40-28T
42-30T
44-30T
mm, 31.8mm and install it to a L size
104 / 64 mm
88 mm
adapter.
165, 170, 175, 180 mm
170, 172.5, 175, 180 mm
46.8 mm
48.8 mm
68, 73 mm
68, 73 mm
BC1.37 (68, 73mm)
BC1.37 (68, 73mm)
SM-BB90-A
SM-BB90-A
To shift from the larger chainring to the smaller chainring
(Lever B)
When lever (B) is pressed once, there is a shift of one step from the
larger chainring to the smaller chainring.
Example:
From larger chainring to smaller chainring.
Lever (B)
• 2-WAY RELEASE
5
Use the TL-FC16/18 to tighten the cap.
Tightening torque: 0.7 - 1.5 N·m {6 - 13 in. lbs.}
6
Push in the stopper plate and check that the plate pin is
securely in place, and then tighten the bolt of the left crank
arm. (5 mm Allen key)
Note :
Each of the bolts should be evenly and equally
tightened to 12 - 14 N·m {106 - 122 in. lbs.}.
TL-FC32
Wide groove area
4
5
1
6
2
Inner cover
Note :
Set the stopper plate in the right direction as shown
in illustration.
I Spacer installation method
(1) Check whether the width of the bottom
bracket shell is 68 mm or 73 mm.
X = Available
(2) Next, install the adapter while referring to the
FD-M986-D
illustrations below.
X
Spacer
X
14, 12T
66° - 69°
Band Type
Bracket Type
38T
40-44T
68 mm
68 mm
F
BB mount-type
A
bracket
F
A
F
A
F
A
F
A
73 mm
73 mm
Chainstay angle
F
A
* If using a bottom bracket shell having a width of 68 mm which is a
band type, an 1.8 mm spacer and a 0.7 mm spacer can be used
together instead of a 2.5 mm spacer.
Chain length
Add 2 links (with the chain on both
Largest sprocket
the largest sprocket and the large
chainring)
Chain
Installation of the shifting lever
Use a handlebar grip with a maximum
outer diameter of 32 mm.
Tightening torque :
3 N·m {27 in. lbs.}
The shifting lever position can be
adjusted by sliding it to the left or right.
Tightening torque :
2.5 N·m {22 in. lbs.}
• Install the shifting lever in a position where it will not obstruct
brake operation and gear shifting operation.
• Do not use in a combination which causes brake operation to be
obstructed.
Note:
When installing the components to carbon frame/handle bar
surfaces, verify with the manufacturer of the carbon frame/parts for
their recommendation on tightening torque in order to prevent over
tightening that can cause damage to the carbon material and/or
under tightening that can cause lack of fixing strength for the
components.
Refer to the FD-M985 / M985-E / M985-E2 / M986 / M986-D
(Front Derailleur) Service Instructions for details on installing
the front derailleur and SIS adjustment.
Connecting and securing the inner cable
3
Switch the mode converter to the 3x (triple mode) position, and then
check the lowest position. Operate lever B two times or more to set
the lever to the lowest position. Remove the inner hole cover, and
install the cable.
Lever (B)
Inner cable
Inner hole cover
Mode converter
Mode select switch
Note:
Do not force the mode select switch to turn. If you force it to turn, it
will break.
Operate lever A once to set it to the middle position. Switch the
mode converter to the 2x (double mode) position.
Lever (A)
Mode converter
F
A
Mode select switch
2.5 mm
Note:
The mode converter cannot be switched while the lever is at the
lowest position. Be sure to operate lever (A) one or more times
before switching. Do not turn the mode converter by force, otherwise
it may break.
Inner hole cover
Install the inner hole cover by turning it as
shown in the illustration until it stops.
Do not turn it any further than this, otherwise
it may damage the thread on the cover.
Cutting the outer casing
When cutting the outer casing, cut the opposite end to the end with
the marking. After cutting the outer casing,
make the end round so that the inside of the
hole has a uniform diameter.
Attach the same outer end cap to the cut end of the outer casing.
Large chainring
Outer end cap
Replacement of the shifting lever unit
Disassembly and reassembly should only be carried out when
4 mm Allen key
replacing the shifting lever unit.
Bracket
Unit fixing bolt
Tightening torque:
2.5 N·m {22 in. lbs.}
Washer
Adjustment barrel
Shifting lever mounting screws (Small)
Tightening torque:
0.08 N·m {0.7 in. lbs.}
Shifting lever mounting screws (Large)
Tightening torque:
0.14 N·m {1.2 in. lbs.}
1. Loosen the cable fixing bolt (nut) of the front derailleur, and then
pull the inner cable out of the shifting lever unit in the same way
as when installing the inner cable.
2. Remove the adjustment barrel.
3. First remove the unit fixing bolt.
4. Remove the four shifting lever mounting screws, and then remove
the shifting lever unit as shown in the illustration.
5. To assemble, align the shifting lever unit and the bracket and then
secure the shifting lever mounting screws.
6. Place the washer onto the bolt, and then secure the unit fixing
bolt.
7. Install the adjustment barrel.
This service instruction explains how to use and maintain the
Shimano bicycle parts which have been used on your new bicycle.
For any questions regarding your bicycle or other matters which
are not related to Shimano parts, please contact the place of
purchase or the bicycle manufacturer.
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
* Service Instructions in further languages are available at :
http://techdocs.shimano.com
Please note: specifications are subject to change for improvement without notice. (English)
© Jul. 2010 by Shimano Inc. XBC SZK Printed in Japan.