Siemens EH8..MC2 series Buku Petunjuk - Halaman 13

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Kompor Siemens EH8..MC2 series. Siemens EH8..MC2 series 20 halaman.

Halaman Cetak

Time programming function

This function may be used in two different ways:

to automatically switch off a hotplate.

■

as a timer.

■

Turn off a hotplate automatically

Enter the cooking time for the desired hotplate. The hotplate

turns off automatically once the time has elapsed.

Programming

Select the desired power level.

Press the

symbol. The

up.

‹‹

lights up in the time program function display. To

select another hotplate, press the

until the

indicator for the desired hotplate lights up.

Select the required cooking time in the programming panel.

The possible previous setting is, from left to right 1, 2, 3, etc.,

up to 10 minutes. Within the next 10 seconds, continue past

the options in the programming panel until reaching the

desired time.

After a few seconds the cooking time begins to count down.

Automatic programming

If the previous setting from 1 to 5 is pressed in the

programming panel, the cooking time is reduced by one

minute, if it is held down the time is automatically reduced to

one minute.

If the previous setting from 6 to 10 is pressed in the

programming panel , the cooking time is increased by one

minute, if it is held down the time is automatically increased to

99 minutes.

Once the time has elapsed

The hotplate switches off. An audible signal sounds and

appears in the time program function display for 10 seconds.

The

indicator lights up. Pressing the

indicators and stops the signal.

Automatic time limitation

If the hotplate remains in use for a long time and no changes

are made in the settings, the automatic time limitation function

is triggered.

The hotplate stops heating. On the hotplate display,

flash alternately.

The indicator goes out when any symbol is pressed. The

hotplate can now be reset.

indicator of the hotplate lights

symbol several times

symbol turns off the

Changing or cancelling the time

Press the

lights up. Change the cooking time in the programming panel,

or set to

‹‹

Automatically switch off a hotplate with the deep-frying

function

When cooking using the deep-frying function, the programmed

cooking time begins to count down once the selected hotplate

reaches the desired temperature.

Notes

If a cooking time has been programmed in several zones, it

■

can be set to display all time values. To do this, press the

symbol several times until the

hotplate lights up.

Cooking times of up to 99 minutes can be programmed.

■

Automatic timer

With this function you may select a cooking time for all

hotplates. Once a hotplate is switched on, the selected time will

begin to count down. The hotplate will automatically switch off

when the cooking time has elapsed.

Instructions on activating the timer are found in the chapter

entitled "Basic settings".

Note: The cooking time of a zone may be cancelled or

changed:

Press the

indicator lights up. Change the cooking time in the

programming panel, or set to

The timer

The timer can be set for periods of up to 99 minutes. It is

independent of the other settings. This function does not

automatically switch off a hotplate.

Programming

Press the

up.

lights up in the time program function display.

‹‹

Select the desired time in the programming panel.

The timer starts to count down after a few seconds.

Once the time has elapsed

A warning beep sounds. In the time program function display

is shown, and the

‹‹

the indicators turn off.

Pressing the

beep.

Changing or cancelling the time

Press the

up. Change the cooking time in the programming panel, or set

‹‹

When the automatic time function is used, it is governed by the

selected power level (from 1 to 10 hours).

and

‰

symbol several times until the desired

indicator for the required

symbol several times until the required

‹‹

symbol several times until the

indicator comes on. After 10 seconds

symbol turns off the indicators and stops the

symbol several times until the

indicator

indicator lights