ACU-RITE 00595 Buku Petunjuk - Halaman 3

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Stasiun Cuaca ACU-RITE 00595. ACU-RITE 00595 10 halaman. Professional wireless weather station with wind sensor & atomic clock

Halaman Cetak

MOUNTING THE WIRELESS WIND

SPEED AND WIND DIRECTION

SENSOR:

Before permanently mounting the wind

speed bracket, make sure that the

wind-fan and wind-vane can rotate freely

without any disruption. Also note that

the wind speed sensor bracket arm

must be pointing north. The wind speed

sensor should be positioned to allow the

wind to flow around the sensor

unhindered from all directions for the

most accurate and correct readings.

OPTIONAL POLE MOUNTING:

Both sensors are designed to mount in

two ways, either to flat surfaces like wood

posts, or to 3/4" schedule 40 PVC pipe

(the outside dimension of the pipe

actually measures approximately 1, 1/16").

The pipe mounting method is often

referred to in these instructions.

The ideal mounting scenario would be for

the wireless thermo-hygrometer to be

mounted on the north side of the building

and for the wind sensor to be mounted

well away from the building and high in the

air. Please test the wireless signal range

before permanently mounting.

Since PVC pipe is somewhat flexible, if a

tall wind sensor mast is being erected, a

larger diameter PVC pipe should be used

for the base with a reducer fitting placed

at the top.

Plastic pipes used for mounting are

non-conductive and reduce the likelihood

of lightening strikes.

BATTERIES

(not included)

NOTE: Do not install batteries in any of the units until you have read through the initial

set-up steps in their entirety.

BATTERY TYPE:

INDOOR UNIT: "AA" (3) alkaline type batteries can be used for the indoor unit.

WIRELESS OUTDOOR UNITS: It is recommended that LITHIUM type "AA" batteries be used

in any outdoor units when the temperature drops below -4ºF. Alkaline batteries may freeze

at very low temperatures and will fail to provide adequate power to the wireless units.

MAIN UNIT BATTERY REPLACEMENT:

When the low battery indicator icon becomes present, it is recommended that you change

the batteries. Replace only with the same or equivalent type of fresh alkaline batteries.

BATTERY INSTALLATION:

For the first installation, insert the batteries into the two WIRELESS SENSORS FIRST and

then into the main unit.

Thermo-Hygrometer Sensor: (See illustration next page) Rotate and pull the top casing

from the bottom cone by turning the unit upside down and rotating counter-clock wise

until casing pulls apart. Insert 2 fresh "AA" batteries (batteries not included). Replace

the battery compartment cover and rotate the top back into the bottom piece.

Wind Sensor: (See illustration next page) Twist off the top from the bottom and open the

battery cover located on the bottom of the sensor. Insert 2 fresh "AA" batteries.

(Batteries not included). Replace battery door cover by putting battery cover on half way

and then sliding into place. Twist on the top to the bottom piece.

Main Unit: Open the battery cover located on the back of the unit and insert 3 fresh "AA"

batteries. (Batteries not included). Replace battery door cover.

NOTE: When reinstalling the batteries while holding down the "CLEAR" button, all user

settings will be cleared and the unit will set back to the factory default settings. If no

button is pushed during battery replacement, the last record and user settings will be

saved.

NOTE: When installing batteries, always install according to the polarity indicated in the

battery compartment ( + to + and - to - ).

LOW BATTERY INDICATOR:

Low Battery

Low battery indicator is displayed on the main unit for the main unit and all wireless

sensors. When replacing the batteries, please follow the battery installation procedure as

mentioned in this instruction manual. When installing or replacing batteries do not mix

battery types or old batteries with new batteries.

BATTERY REPLACEMENT:

When the low battery indicator icon becomes present, it is recommended that you change

the batteries. Replace only with the same or equivalent type of fresh alkaline batteries. This

method of battery replacement ensures there will be no loss in MIN/MAX and history data.

However, if main unit or sensors have remained without batteries for an extended period of

time, the main unit will lose the MIN/MAX and all weather data recordings and will have to be

synchronized again.

Battery O.K.