Cisco MXP Series Manual Antarmuka Fisik - Halaman 24
Jelajahi secara online atau unduh pdf Manual Antarmuka Fisik untuk Sistem Konferensi Cisco MXP Series. Cisco MXP Series 28 halaman.
Halaman Cetak
MXP Series Codecs
Contents
Net socket (applies to 3000 MXP Net only)
V35 DTE to DCE
Pin
Signal name
Direction
Description
↔
1
FGND
Frame GND on equipment
→
11
SD(A)
Send Data / Transmit
→
12
SD(B)
Send Data / Transmit
←
13
RD(A)
Receive Data
←
14
RD(B)
Receive Data
←
15
SCR(A)
Signal Clock Receive
←
16
SCR(B)
Signal Clock Receive
←
17
SCT(A)
Signal Clock Transmit
←
18
SCT(B)
Signal Clock Transmit
↔
19
GND
Signal GND
1
←
22
RLSD(CD)
Received Line Signal Detector / Carrier Detect
23
RLSD(GND)
1
Signal GND - This pin is connected to ground
←
for correct operations
←
24
RI
Ring Indicator
→
25
LOS
Loss of Signal (KG194)
→
26
DTR
Data Terminal Ready
RS449 DTE to DCE
Pin
Signal name
Direction
↔
1
FGND
Frame GND - Frame GND is connected to pin
1 on DTE
→
11
SD(A)
Send Data
→
12
SD(B)
Send Data
←
13
RD(A)
Receive Data
←
14
RD(B)
Receive Data
←
15
RT(A)
Receive Timing
←
16
RT(B)
Send Timing
←
17
ST(A)
Send Timing
←
18
ST(B)
Send Timing
↔
19
GND
GND - 1) This pin is connected to ground for
1
correct operations
→
20
TR(A)
Terminal Ready
→
21
TR(B)
Terminal Ready
←
22
RR(A)
Carrier Detect / Receiver Ready
←
23
RR(B)
Carrier Detect / Receiver Ready
←
24
IC
Incoming Call
→
25
LOS
Loss of Signal (KG194)
D14790.01 MXP Series Codec Physical Interface Guide, May 2011.
© 2011 Cisco Systems, Inc. All rights reserved.
Introduction
Description
Codec 6000 MXP
Note the following:
V.10 (RS423): For balanced signals a 0 = low
voltage, is defined as terminal A positive with
respect to terminal B. For unbalanced signals a
0 = low voltage, is defined as terminal positive
with respect to GND. Cable length for Leased
Line Control should not exceed 20 m.
RS 366: All balanced inputs and outputs (A
and B) use balanced line signals according to
V.11 (RS 422), while single ended signals are
in accordance with V.10 (RS423). The 0 = low
voltage definitions are the same as for V.10
above. Max cable length, as for V.10 above.
X.21: Signals are as for RS 366 above. Cable
length should not exceed 50 m.
HD D-SUB 26 pin-out
External view of socket
1
9
10
18
19
26
X.21 DTE to DCE
Pin
Signal
Direction
Description
name
↔
1
FGND
Frame GND
→
11
T(A)
Send Data / Transmit
→
12
T(B)
Send Data / Transmit
←
13
R(A)
Received Data / Receive
←
14
R(B)
Received Data / Receive
←
15
S(A)
Signal Element Timing
←
16
S(B)
Signal Element Timing
→
20
C(A)
Terminal Ready / Control
→
21
C(B)
Terminal Ready / Control
←
22
I(A)
Carrier Detect
←
23
I(B)
Carrier Detect
24
Physical interface guide
Codec 3000 MXP
Codec 3000 MXP
Net interface socket. 1 × X.21
/ V.35 / RS449 with 1 × RS366
Call Control up to 2 Mbps
RS366 DTE to DCE
Pin
Signal
Direction
name
↔
1
FGND
→
2
DPR
←
3
ACR
→
4
CRQ
←
5
PND
←
6
DLO
→
7
NB1
→
8
NB2
→
9
NB4
→
10
NB8
Contact us
Description
Frame GND
Digit Present
Abandon Call & Retry
Call Request
Present Next Digit
Data Line Occupied
Digit Bit 1
Digit Bit 2
Digit Bit 4
Digit Bit 8
www.cisco.com