Cisco TelePresence Profile 65 Panduan Memulai - Halaman 27

Jelajahi secara online atau unduh pdf Panduan Memulai untuk Sistem Konferensi Cisco TelePresence Profile 65. Cisco TelePresence Profile 65 42 halaman. Telepresence ex, mx, quick set c20, codec c, sx20 quick set, profile series video systems
Juga untuk Cisco TelePresence Profile 65: Panduan Pengguna (44 halaman), Panduan Memulai (46 halaman)

Halaman Cetak

Cisco TelePresence Systems

GettinG started Guide

Table of contents

Introduction

Web interface

Configuring H.323 and SIP

(when not set by a provisioning system)

To get online and ready to place and receive calls, your

system must be set up properly. Your system will use either

the H.323 protocol or the SIP protocol for video calls.

NoTE:

Contact your system administrator, or service

provider, for information about the network settings.

For networks administered through Cisco TMS (Cisco

TelePresence Management Suite) your Cisco TMS

administrator will help you to get online.

Back to task overview

User interfaces

Configuration

H.323

If in doubt for any of the parameters below, contact your

system administrator or your service provider.

1. Go to the

Configuration

tab and select

Configuration.

Open the

H323

settings from the left column.

2. Under the

H323 Alias

heading, enter the

number in their respective input fields.

3. Go to the

Gatekeeper

heading.

If you want the system to obtain the H.323 gatekeeper

address automatically, select

down list; if you want to enter the address manually,

select

Manual.

If set to

Manual

enter the gatekeeper

corresponding input field. Click

4. If the H.323 gatekeeper requires authentication and

you want your system to authenticate itself to the

gatekeeper, go to the

Authentication

select

in the

Mode

drop down list. Then enter the

LoginName

and

Password

in the corresponding input

fields. Click

to save the change.

Otherwise, select

Off

in the

Mode

5. Go to the

Diagnostics

tab and select

to verify the H323 settings.

If you successfully registered to a Gatekeeper the

will show

Registered

in the H323 section.

Please check the Administrator guide for your product if you

want to change the other H.323 settings.

Appendices

SIP

If in doubt for any of the parameters below, contact your

system administrator or your service provider.

Advanced

1. Go to the

Configuration.

Open the

and

E164

2. Enter the SIP URI in the

display name in the

save the change.

3. Select the preferred transport protocol from the

DefaultTransport

Auto

in the

Discovery

drop

system will first try to connect using TLS, then TCP, and

finally UDP.

Address

in the

4. Select a proxy type in the

to save the change.

default type is Standard.

5. Go to the

If you want the system to obtain the SIP proxy address

heading and

automatically, select

list; if you want to enter the address manually, select

Manual.

If you select

drop down list.

corresponding input field. Click

System Information

6. If the SIP proxy requires authentication you must enter a

Status

Go to the

LoginName

fields. Click

7. Go to the

to verify the SIP settings.

If you successfully registered to a SIP server the

will show

Please check the Administrator guide for your product if you

want to change the other SIP settings.

Configuration

tab and select

Advanced

SIP

page from the sidebar on the left.

URI 1

input field, and optionally a

DisplayName

input field. Click

drop down list. If you select Auto, the

Type

drop down list. The

Proxy 1

heading.

Auto

in the

Discovery

drop down

Manual

enter the proxy

Address

in the

to save the change.

Authentication 1

heading and enter the

and

Password

in the corresponding input

to save the change.

Diagnostics

tab and select

System Information

Status

Registered

in the SIP section.