Artrom DHP-20R Panduan Pemilik - Halaman 11

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Dehumidifier Artrom DHP-20R. Artrom DHP-20R 14 halaman.

Halaman Cetak

CONTROL PADS ON THE DEHUMIDIFIER

NOTE: The control panel of the unit you purchased may be slightly different according to the

models.

High fan

Timer on/off

Ion operation on

indicator light

Fig.1

Control pads

When you push the button to change

operation modes, the unit will make

a beep sound to indicate that it is

changing modes.

Power Pad

Press to turn the dehumidifier on and off.

NOTE: When the compressor startups or stops

running,the unit may make a loud voice,it is normal.

Mode Pad

Press to select the desired operation mode from

Dehumidifying,Dryer,Continuous dehumidifying and

Smart dehumidifying.

NOTE: Dryer and Smart dehumidifying modes are

optional.

: Down/Up Pads

Humidity Set Control Pads

The humidity level can be set within a range of

35%RH(Relative Humidity) to 85%RH(Relative

Humidity) in 5% increments.

For drier air, press the

pad and set to a lower

percent value(%).

For damper air, press the

pad and set a higher

percent value(%).

TIMER Set Control Pads

Use the Up/Down pads to set the Auto start and

Auto stop time from 0.0 to 24.

Continuous

Smart dehumidifying

operation on

Dryer operation

operation on indicator

indicator light

on indicator light

light

Bucket full

indicator light

Timer Pad

Press to initiate the Auto start and Auto stop feature,

in conjuction with the

and

key pads.

Turbo Pad

Control the fan speed. Press to select either High

or Normal fan speed. Set the fan control to High for

maximum moisture removal. When the humidity has

been reduced and quiet operation is preferred, set

the fan control to Normal.

Ion Pad(optional)

Press to activate the ionizer. Anions ar automatically

generated by ionization. The anions deactive the

airborne chemical vapors and dust particles. Press

it again to stop the function.

Display

Shows the set % humidity level from 35% to 85% or auto

start/stop time (0~24) while setting, then shows the actual

( ± 5% accuracy) room % humidity level in a range of

RH(Relative Humidity) to 90%RH(Relative Humidity).

Error Codes and Protection Codes:

Unit operation on

indicator light

AS- Humidity sensor error--Unplug the unit and plug it back

in. If error repeats, call for service.

ES- Temperature sensor error-- Unplug the unit and plug it

back in. If error repeats, call for service.

Other features

Bucket Full Light

Glows when the bucket is ready to be

emptied, or when the bucket is removed

or not replaced in the proper position.

Auto Shut Off

The

dehumidifier

shuts off when the bucket is full,

or when the bucket is removed or not replaced in

the proper position.When the setting humidity is

reached, the unit will be shut off automatically.

For some models,the fan motor will continue

operating.

Auto Defrost

When frost builds up on the evaporator coils, the

compressor will cycle off and the fan will continue

to run until the frost disappears.

NOTE:When Auto defrosting operation,the unit may

make a voice of refrigerant flowing,it is normal.

Wait 3 minutes before resuming operation

After the unit has stopped, it can not be restart

opertation in the first 3 minutes. This is to protect

the unit. Operation will automatically start after

3 minutes.

Smart dehumidifying mode(optional)

At smart dehumidifying mode, the unit will automatically

control room humidity in a comfortable range 45%~55%

according to the room temperature. The humidity setting

function will be invalid.

CONTROL PADS ON THE DEHUMIDIFIER

P1- Unit is defrosting-- Allow the unit time to automatically

defrost. The protection will clear after the unit self defrosts.

30%

P2- Bucket is full or bucket is not in right position-- Empty

the bucket and replace it in the right position.

E3- Unit malfunction-- Unplug the unit and plug it back in. If

error repeats, call for service.

EC-Refrigerant leakage detection-- With this new technology,

the display area will appear EC when the unit detects

refrigerant leakage ,call for service.

Auto-Restart

If the unit breaks off unexpectedly due to the power cut,

it will restart with the previous function setting automa-

tically when the power resumes.

Setting the Timer

When the unit is on, first press the Timer

button, the Timer Off indicator light

illuminates. It indicates the Auto Stop

program is initiated. Press it again the

Time On indecator light illuminates.It

indicates the Auto Start is initiated.

When the unit is off, first press the Timer

button, the TIMER ON indicator light

illuminates. It indicates the Auto Start

program is initiated. Press it again the

Time Off indecator light illuminates.It

indicates the Auto Stop is initiated.

Press or hold the UP or DOWN pad to

change the Auto time by 0.5 hour incre-

ments, up to 10 hours, then at 1 hour

increments up to 24 hours. The control

will count down the time remaining until

start.

The selected time will register in 5 seconds

and the system will automatically revert

back to display the previous humidity

setting.

When the Auto start & Auto stop times are

set, within the same program sequence,

TIMER ON OFF indicator lights illuminate

identifying both ON and OFF times are

now programmed.

Turning the unit ON or OFF at any time or

adjusting the timer setting to 0.0 will cancel

the Auto Start/Stop function.

When LED display window displays the

code of P2, the Auto Start/Stop function

will also be cancelled.