Flying Industry Development 0020195 Manuale d'uso - Pagina 2

Sfoglia online o scarica il pdf Manuale d'uso per Ricevitore Flying Industry Development 0020195. Flying Industry Development 0020195 3. Rf wireless receiver

Stampa la pagina
Setting different control modes (We have set the receiver as Toggle control mode before delivery. If you want to use other control modes, do as
following operation):
Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle (with transmitter C-2): Press -> On; Press again -> Off.
Press the button 1 of the transmitter: Turn on the relay 1 (connect "COM1" and "NO1", disconnect "NC1" and "COM1"), the lamp 1 is on.
Press the button 1 again: Turn off the relay 1 (disconnect "COM1" and "NO1", connect "NC1" and "COM1"), the lamp 1 is off.
Press the button 2 of the transmitter: Turn on the relay 2 (connect "COM2" and "NO2", disconnect "NC2" and "COM2"), the lamp 2 is on.
Press the button 2 again: Turn off the relay 2 (disconnect"COM2" and "NO2", connect "NC2" and "COM2"), the lamp 2 is off.
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary (with transmitter C-2): Press and hold -> On; Release -> Off.
Press and hold button 1 of the transmitter: Turn on the relay 1 (connect "COM1" and "NO1", disconnect "NC1" and "COM1"), the lamp 1 is on.
Release the button 1: Turn off the relay 1 (disconnect"COM1" and "NO1", connect "NC1" and "COM1"), the lamp 1 is off.
Press and hold button 2 of the transmitter: Turn on the relay 2 (connect "COM2" and "NO2", disconnect "NC2" and "COM2"), the lamp 2 is on.
Release the button 2: Turn off the relay 2 (disconnect"COM2" and "NO2", connect "NC2" and "COM2"), the lamp 2 is off.
Setting control mode Latched: Do not connect Jumper-1 and Jumper-2.
Control mode Latched (with transmitter C-3): Press button -> On; Press another button -> Off.
Press button C of the transmitter: Turn on the relay 1, the lamp 1 is on; and turn off the relay 2, the lamp 2 is off.
Press button B of the transmitter: Turn on the relay 2, the lamp 2 is on; and turn off the relay 1, the lamp 1 is off.
Press button A of the transmitter: Turn off two relays, two lamps are off.
Setting control mode Momentary + Toggle (with transmitter C-2): Connect Jumper-1 and Jumper-2
Control mode Momentary (Channel 1): Press and hold -> On; Release -> Off.
Press and hold button 1 of the transmitter: Turn on the relay 1, the lamp 1 is on.
Release the button 1: Turn off the relay 1, the lamp 1 is off.
Control mode Toggle (Channel 2): Press -> On; Press again -> Off.
Press the button 2 of the transmitter: Turn on the relay 2, the lamp 2 is on.
Press the button 2 again: Turn off the relay 2, the lamp 2 is off.
Wired control terminals:
The receiver has manual control terminals, you can connect external devices, sensors, or manual switches to control the receiver.
1) Signal input:
You can connect external devices (with low level output signal) to manual terminals 1 (Signal +), 2 (Signal +), and terminal 3 (Signal -) , then the
external device's output signal can control the receiver.
When the external device outputs low level signal to manual terminal 1 and terminal 3, turn on the relay 1, the lamp 1 is on.
When t
external
stops
he
device
When the external device outputs low level signal to manual terminal 2 and terminal 3, turn on the relay 2, the lamp 2 is on.
When t
external
stops
he
device
2) The manual switches:
You can connect manual switches to manual terminals 1, 2 and 3, then you can use manual switches to control the receiver.
When connect terminals 1 and 3, turn on the relay 1, the lamp 1 is on.
And when disconnect terminals 1 and 3, turn off the relay 1, the lamp 1 is off.
When connect terminals 2 and 3, turn on the relay 2, the lamp 2 is on.
And when disconnect terminals 2 and 3, turn off the relay 2, the lamp 2 is off.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.
2) Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
Delete all transmitters:
We have learned remote control to the receiver. If you don't want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.
signal, turn off the relay 1, the lamp 1 is off.
to output
signal, turn off the relay 2, the lamp 2 is off.
to output
SHENZHEN FLYING INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com