Auber Instruments JSL-64A Manuale di istruzioni - Pagina 3

Sfoglia online o scarica il pdf Manuale di istruzioni per Timer Auber Instruments JSL-64A. Auber Instruments JSL-64A 5. 1/32 din general purpose timer

Stampa la pagina

AUBER INSTRUMENTS

6. Parameter Settings

All parameters are listed in the table below.

Press and hold SET key for 3 seconds to enter the menu mode. For each

parameter setting, use UP or DOWN key to select different programming

values. Press SET key to confirm then exit. Please check figure 3 for details.

For the definition of each programming value, see Table 1.

Table 1. Parameter Description.

Code

Description

(Short-press SET key)

Set value for T1

Set value for T2

(Long-press SET key for 3 seconds)

Timer function, operating

FUNC

Func

mode

T1U

T1u

T1 timer unit

T2U

T2u

T2 timer unit

TDIR

Tdir

Timer counting direction

OUT

Relay output mode

Out

RUN

run

Timer triggering action

Relay action when STP

STOP

stop

key is pressed

Relay action when PAU

PAUS

paus

key is pressed

* Please note that ESP function is a new feature added to JSL-64A. It is not available in

JSL-64.

** Please note that STOP parameter will only appear in the menu when FUNC = SDL

and OUT = ONDL.

Details about each parameter

Note 1. T1 is the set value in Single Delay (SDL) mode. It is also the first set

value in in Delayed Interval Mode (DINT) and the Cycled Mode (CYCL) mode.

Note 2. T2 is the second set value in Delayed Interval Mode (DINT) or in the

Cycled Mode (CYCL). This parameter will only be displayed if the Timer Mode

FUNC is set to either DINT or CYCL mode.

Note 3: FUNC is the timer operating mode, it can be set to SDL, DINT, CYCL,

or EST.

SDL (Single Delay): The timer counts a single period of time that is

defined in T1. The relay can either be turned on during this period of timer or it

can be turned on at the end of this period of time, depends on the OUT setting.

When OUT = OFDL, the relay turns on at the beginning when timer starts

counting, and turns off when the counting stops. When OUT = ONDL, the relay

2021.03

Range

Initial

Set Values

1:10

1.10

Parameters

SDL,

DINT,

sdl

CYCL,

EST *

M:S

M:S,

H:M

UP, DN

OFDL,

OFDL

ONDL

RST, PU

RST

0, 1

stays off when timer starts counting, and the relay turns on when the timer

reaches the set value till the RST (reset) key is pressed or when the power to

the device is cycled. Please refer to Note 6 for details about OUT parameter.

In Single Delay and On-Delay mode (i.e., FUNC = SDL, OUT = ONDL), a

special parameter "STOP" will appear in the parameter menu. For details

please refer to the Note 8 below.

DINT (Delayed Interval): The timer will count time for two periods of time,

T1 and T2, and then stops. Relay action depends on the OUT setting. When

OUT =OFDL, the relay turns on at the end of T1, stays on during T2 time, and

then turns off at the end of T2 time. When OUT = ONDL, the relay turns on at

the beginning at T1 time, turns off at the end of T1 time, stays off during T2,

and then turns on again at the end of T2 time. This is a single action process.

CYCL (Cycle): The timer will repeat a counting cycle that consists of two

periods of time, T1 and T2. The relay turns on/off during each cycle depending

on the OUT setting. When OUT = OFDL, the relay turns on at the end of T1,

stays on during T2 time, and then turns off at the end of T2 time. When OUT =

3 *

ONDL, the relay turns on at the beginning at T1 time, turns off at the end of T1

time, stays off during T2, and then turns on again at the end of T2 time. This

cycle will be immediately repeated till it is stopped or reset.

EST (Espresso Shot Timer): This is a special mode designed for counting

the shot time (brew time) on an espresso machine. The timer display resets to

zero and it starts counting up when the pin 9 and 10 are shorted together. The

timer stops counting when terminal 9 and 10 are disconnected. The time unit is

determined by the parameter T1U. Pressing the RST key can clear the display.

The relay output, STP key, and PAU key are not functional in this mode. The

settings of parameter T2U, TDIR, OUT, RUN, STOP, and PAUS are irrelevant

8 **

to this mode.

Note 4. T1U and T2U define the time unit for T1 and T2. (Note, T2 is only

available when FUNC = DINT or CYCL).

Settings

M:S

H:M

Note 5. TDIR determines the Timer Counting Direction.

UP: counting up.

DN: counting down.

Note 6. OUT determines the relay output status as the timer runs.

OFDL (off-delay): the relay will turn ON when timer starts counting and

the relay will turn OFF when the timer reaches the set value.

ONDL (on-delay): the relay will stay OFF when the timer starts counting

and the relay will turn ON when the timer reaches the set value.

Note 7. RUN determines how does the timer start counting.

PU (power up): the timer starts counting when the device is powered up.

RST (reset): the timer starts when reset button is pressed and released.

WWW.AUBERINS.COM

Description

Range

Seconds

0.01 s ~ 99.99 s

Minutes: Seconds

1 s ~ 99 m 59 s

Minutes

1 m ~ 9999 m

Hours: Minutes

1 m ~ 99 h 59 m

P3/5