ADEMCO 5800WAVE Manuale di installazione e configurazione

Sfoglia online o scarica il pdf Manuale di installazione e configurazione per Sistema di sicurezza ADEMCO 5800WAVE. ADEMCO 5800WAVE 4. Wireless siren module

Stampa la pagina

GENERAL INFORMATION

The 5800WAVE (Figure 1) is a wireless siren module that

contains an RF receiver and transmitter. The 5800WAVE

provides the following features:

•

May be used with the LYNXR Rev 10 or higher (with

RF enrollment) and LYNXR-EN self-contained controls

or with any other control that supports a 5883

Transceiver Module.

•

Transmits module status, including mounting tamper,

low battery, and AC loss to the control.

•

Transmits supervisory check-in message.

•

AC powered and mounts to any standard duplex

receptacle.

•

Contains a rechargeable battery that provides up to 12

hours of standby operation in the event of AC loss.

LED

Activates Upon

Yellow

Normally off. Blinks to indicate that an RF

message is being sent by the 5800WAVE.

steady during RF Link test.

Green

Normally on (lighted) when AC power is present.

Red

On when the system is armed. Off when the

system is disarmed.

indicates poor RF transmission.

INSTALLATION

To install the 5800WAVE siren, connect the battery, set the

house ID, and enable module supervision, follow the

instructions below.

1. The 5800WAVE must be installed on a

Listed duplex receptacle using the screw

provided.

2. Do not connect the 5800WAVE to a

receptacle controlled by a switch.

3. For 24 hours of standby operation and UL

Listed Fire Installations, use ADEMCO

battery part number WALYNX-RCHB-HC.

Note: The 5800WAVE must be powered overnight for the

battery to reach full capacity.

Connecting the Battery and Setting the House ID

Caution: When opening the case to connect the battery and

set the house ID, use care not to damage the wire leads

connected to the sounder and circuit board when separating

the case front from the back. Refer to figure 2.

Remove the 4 screws located in the back of the unit.

Check that the standby battery is held securely in place

by the two battery clips (Figure 2).

Plug the standby battery connector into the PCB

connector as shown in Figure 2.

Set DIP switches 4-8 to the appropriate House ID (1-31)

See Figure 3. The House ID set by the DIP switches

should match that entered in the control.

Close the 5800WAVE's case and reinstall the 4 screws

removed in step 1.

INSTALLATION AND SETUP GUIDE

During RF Link test, on

Verifying The RF Link

Notes:

Dip switch 6 on the 5883 must be set to ON to enable its RF

transmitter.

The security system control must have the House ID set and

must not be in the Test Mode or Programming Mode when

checking the RF Link.

Plug the 5800WAVE into the AC receptacle at the

desired location. The green LED will light indicating

AC is present and the 5800WAVE is powered.

yellow LED will light for approximately 15 seconds.

•

If the red LED turns on, the RF link is bad. Relocate

the 5800WAVE to another AC receptacle (closer to the

control) and repeat step 1 to verify the RF Link.

•

If the red LED remains off, the RF link is good and you

may complete the installation at this location.

Unplug the 5800WAVE and proceed to "Enable Module

Supervision".

Enabling Module Supervision

The 5800WAVE is supervised by the control for loss of RF

check-in transmissions, low battery, loss of AC, and

mounting tamper.

The 5800WAVE reports AC loss and low battery as Low

Battery to the control (and will not cause an alarm when

the control is armed).

An AC loss exists if Low Battery is displayed on the control

keypad (with the programmed zone number) and the Green

LED on the 5800WAVE is off.

Program the 5800WAVE in the control as a zone and enroll

its serial number as described using the installation and

setup guide supplied with the control and the information

below.

Note the following when enrolling:

Zone type = 5 (trouble by day / alarm by night)

Input type = 3 (RF)

Loop number = 1

When prompted for the serial number, you can either

enter it manually or transmit from the device.

To enter the serial number manually, read the

number from the label on the device and enter it

via the control's keypad (referring to the zone

programming section of the Installation and Setup

Guide for the control).

transmit

5800WAVE into an AC receptacle.

(within 15 seconds) place the tamper magnet next

to the tamper position indicator lines on the case

(figure 4) and wait until the yellow LED turns off,

and

transmission.

The yellow LED will flash when the transmission is

sent.

When the enrollment is complete, exit programming

mode and unplug the 5800WAVE. Proceed to step 3 if

mounting tamper is desired.

Completing Installation.

K0584V1 Rev. B 2/03

Wireless Siren Module

the

serial

number,

then

remove

the

magnet

Otherwise proceed to

5800WAVE

The

plug

the

Immediately

cause