Autonics Ai-M-42SA Manuale - Pagina 12
Sfoglia online o scarica il pdf Manuale per Controllore Autonics Ai-M-42SA. Autonics Ai-M-42SA 16. Pulse train input type, servo system, dc type
Stampa la pagina
两相步进电机马达样本闭环步进电机驱动器说明书 韩国Autonics步进伺服马达选型样本pdf资料
3. Connection with load
When connecting the load, be sure of the center, tension of the belt, and parallel of the pulley. When connecting the load such as a pulley,
a belt, be sure of the allowable thrust load, radial load, and shock. Tighten the screw for a coupling or a pulley not to be unscrewed. When
connecting a coupling or a pulley on the motor shaft, be sure of damage of the motor shaft and the motor shaft bearing. Do not disas-
semble or modify the motor shaft to connect with the load.
Direct load connection
with coupling
Flexible
coupling
Ball screw or
TM screw
※ Use Autonics flexible coupling (ERB Series).
When connecting the load directly (ball screw,
TM screw, etc) to the motor shaft, use a flexible
coupling as shown in the above figure. If the
center of the load is not matched to that of
shaft, it may cause severe vibration, shaft
damage or shortened life cycle of the shaft
bearing.
4. Installation condition
Install the motor in a place that meets certain conditions specified below.
It may cause product damage if instructions are not following.
①The inner housing installed indoor (This unit is manufactured for attaching to equipment. Install a ventilation device.)
②Within 0 to 50℃ (at non-freezing status) of ambient temperature
③Within 20 to 90%RH (at non-dew status) of ambient humidity
④The place without explosive, flammable and corrosive gas
⑤The place without direct ray of light
⑥The place where dust or metal scrap is not entered into the unit
⑦The place where water, oil, or other liquid are not touched
⑧The place where strong alkali or acidity does not exist closely
⑨The place where easy heat dissipation could be made
⑩The place where no continuous vibration or severe shock
⑪The place with less salt content
⑫The place with less electronic noise occurs by welding machine, motor, etc.
⑬The place where no radioactive substances and magnetic fields exist. It shall be no vacuum status as well.
Applications
AiS Series for moving axis at
奥托尼克斯电子中国autonics电机热线 4006-022-002
Closed-Loop Stepper Motor System
Load connection with pulley,
belt, and wire
The motor shaft and the load shaft should be
parallel. Connect the motor shaft and the line
which connects the center of two pulleys to a
right angle.
3D inspector device
Load connection with gear
The motor shaft and the load shaft should be
parallel. Connect the motor shaft to the center
of gear teeth side to be interlocked.
深圳 北京 上海 株洲 天津 青岛
(A)
Photoelectric
Sensors
(B)
Fiber
Optic
Sensors
(C)
Door/Area
Sensors
(D)
Proximity
Sensors
(E)
Pressure
Sensors
(F)
Rotary
Encoders
(G)
Connectors/
Sockets
(H)
Temperature
Controllers
(I)
SSRs / Power
Controllers
(J)
Counters
(K)
Timers
(L)
Panel
Meters
(M)
Tacho /
Speed / Pulse
Meters
(N)
Display
Units
(O)
Sensor
Controllers
(P)
Switching
Mode Power
Supplies
(Q)
Stepper Motors
& Drivers
& Controllers
(R)
Graphic/
Logic
Panels
(S)
Field
Network
Devices
(T)
Software
Q-13