Brother 885-X13 Manuale operativo - Pagina 43

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

If the machine stops operating correctly, check the following possible problems before requesting service. You can

solve most problems by yourself. If you need additional help, the Brother Solutions Center offers the latest FAQs and

troubleshooting tips. Visit us at " http://solutions.brother.com ". If the problem persists, contact your dealer or the

nearest authorized service center.

Symptom

The sewing

machine does

not work.

Fabric being

sewn with the

machine

cannot be

removed.

The needle

breaks.

The upper

thread

breaks.

▼

Possible cause

The main power switch is turned off.

The bobbin-winder shaft is pushed to the

right.

You have not used the foot controller

properly.

Thread is tangled below the needle plate.

The needle is incorrectly installed.

The needle clamp screw is loose.

The needle is bent or blunt.

The upper thread was not threaded

correctly.

You have not used the right combination of

fabric, thread and needle.

The presser foot you are using is not

appropriate for the type of stitch that you

want to sew.

The upper thread tension is too tight.

You are pulling the fabric too much.

You have not fitted the spool properly.

The area around the hole in the needle

plate or the presser foot is scratched.

The bobbin case is scratched.

You have not used a bobbin that has been

designed for this machine.

You have not threaded the upper thread

properly. (For example, you have not fitted

the spool properly, or the thread has come

out of the guide above the needle.)

There are knots or tangles in the thread.

The needle is not appropriate for the thread

you are using.

The upper thread tension is too tight.

How to put it right

Turn on the main power switch.

Move the bobbin-winder shaft to the

left.

Use the foot controller properly.

Lift up the fabric and cut the threads

below it, and clean the race.

Correctly install the needle.

Use the oval screwdriver to firmly

tighten the screw.

Replace the needle.

Correct the upper threading.

Choose a thread and needle that are

appropriate for the type of fabric.

Attach the presser foot that is correct

for the type of stitch that you want to

sew.

Loosen the upper thread tension.

Lightly guide the fabric.

Fit the spool properly.

Replace the needle plate.

Contact your retailer or the nearest

authorized service center.

Replace the bobbin case.

Contact your retailer or the nearest

authorized service center.

Use a bobbin that has been designed

for this machine.

Correct the upper threading.

Remove any knots or tangles.

Choose a needle that is appropriate for

the type of stitch.

Loosen the upper thread tension.

Page

7

13

7

40

7

8

7

16

21

–

26

–

6

16, 24

–

–

12

16

–

21

26

42