AccuTemp STEAM'N'HOLD Manuale d'installazione e d'uso - Pagina 6
Sfoglia online o scarica il pdf Manuale d'installazione e d'uso per Attrezzature per alimenti commerciali AccuTemp STEAM'N'HOLD. AccuTemp STEAM'N'HOLD 15. Vacoom steamer
Stampa la paginaINSTALLATION
BUILDING CODES AND STANDARDS
The appliance must be installed in accordance
with the following building codes:
USA: National Electric Code, ANSI/NFPA-70, state
and local codes. International Plumbing Code
2003, ICC or Uniform Plumbing Code 2003,
IAMPO. Canada: Canadian Electric Code, CSA
C22.2 and state and local codes.
LOCATION AND PLACEMENT
To insure maximum benefit of your warranty;
location, placement and leveling are critical.
The AccuTemp STEAM'N'HOLD™ is designed for
installation on either a commercial kitchen coun-
ter top or an AccuTemp STEAM'N'HOLD™ stand.
Your appliance is equipped with vents to allow
the proper ventilation of air through the electrical
compartment. The vents are located on the bot-
tom and rear panel. To ensure these vents work
properly a minimum 3" (77 mm) clearance from
these vents must be allocated. It is also recom-
mended that the appliance not be placed under
other wet equipment or locations. If located next
to heat producing appliances additional clear-
ance could be required.
LEVELING
This appliance must be installed in a level
condition. An out-of-level condition may cause
improper operation and possible damage.
Damage caused by improper leveling is not
covered by warranty. Use a spirit level, resting
on the top of the appliance cabinet surface, to
ensure it is level front-to-back and left-to-right.
COUNTER-TOP INSTALLATION
If this is a counter-top installation, be sure to
install the rubber foot tips provided with your
appliance onto each foot adjuster of each of the
leg. This will keep the appliance from sliding on
the counter-top under normal use. Once the
rubber foot tips have been installed, rotate the
foot adjusters up or down as needed to level the
appliance side to side and front to back.
SINGLE STAND INSTALLATION WITH
ADJUSTABLE FEET
The AccuTemp SNH10 single stand is equipped
with adjustable height feet and the AccuTemp
SNH11 single stand is equipped with non-
MP4011-2207
The AccuTemp SNH10 single stand is
equipped with adjustable height feet and the
AccuTemp SNH11 single stand is equipped
with non-adjustable height casters. Both
can be used with either a single S3 or S6
model STEAM'N'HOLD™. Before mounting
the appliance on the SNH11 stand, engage
the brakes on the two front locking casters,
pressing on the "ON" handle of the brake
mechanism. To mount the appliance, carefully
lift and place it on the horizontal mounting
brackets, ensuring that the (4) mounting holes
on the underside of the appliance is lined up
with the mounting holes on the brackets. Then,
using a 7/16" wrench, fasten one pair of the ¼"-
20 hex bolts and ¼" split lock washers through
the underside of each stand bracket mounting
hole into the appliance and tighten securely.
With the SNH10 stand, level the appliance by
adjusting the feet found at the ends of each
stand leg, either up or down as needed.
SINGLE STAND INSTALLATION WITH CASTERS
Before mounting the appliance
stand, engage the brakes on the two front
locking casters, pressing on the "ON"
handle of the brake mechanism. To mount
the appliance, carefully lift and place it
on the horizontal mounting brackets,
ensuring that the (4) mounting holes on
the underside of the appliance are lined up
with the mounting holes on the brackets.
Then, using a 7/16" wrench, fasten one
pair of the ¼"-20 hex bolts and ¼" split
lock washers through the underside of
each stand bracket mounting hole into the
appliance and tighten securely.
STEAM'N'HOLD™
on the SNH11
6