Sony BluetoothH MEX-BT5100 Manuale di istruzioni per l'uso - Pagina 31
Sfoglia online o scarica il pdf Manuale di istruzioni per l'uso per Impianto stereo Sony BluetoothH MEX-BT5100. Sony BluetoothH MEX-BT5100 45. Bluetooth audio system
Anche per Sony BluetoothH MEX-BT5100: Installazione/Connessioni (2 pagine), Installazione/Connessioni (2 pagine), Manuale rapido (2 pagine), Specifiche tecniche (2 pagine), Manuale rapido (2 pagine), Manuale rapido (2 pagine)
Stampa la pagina
Instalaci6n/Conexiones
Installation/Connections
Installation/Connexions
Bluetooth™
Audio System
Be
II
A
- -
3-276-519-21 (1)
SONY;
MEX-BT5100
©
2007 Sony Corporation
Printed in Thailand
*
not supplied
non tourni
no suministrado
Connection diagram []]
o
To a metal surface of the car
First connect the black ground lead, then connect the
orange/white striped, yellow, and red power input leads.
e
To the power antenna control lead or power
supply lead of antenna booster amplifier
Noles
It is not necessary to connect this lead if there is no power
antenna or antenna booster,
or
with a manually-operated
telescopic antenna.
When your car has
a
built-in FMIAM antenna in the rearl
side glass. see "Notes on the control and power supply
leads."
e
To AMP REMOTE IN of an optional power
amplifier
This connection
is
only for amplifiers. Connecting any other
system may damage the unit.
o
To the interface cable of a car telephone
o
To a car's illumination signal
Be sure to connect the black ground lead to
a
metal surface
01
the car first.
G
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch
Notes
• If there is no accessory position, connect to the
+
12 V
power (battery) terminal which
is
energized at all times.
Be sure to connect the black ground lead to
a
metal
surface of the car first.
• When your car has
a
built-in FMIAM antenna in the rearl
side glass, see "Notes on the control and power supply
leads."
o
To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground lead to
a
metal surface
01
the car first.
Noles on Ihe control and power supply leads
The power antenna control lead (blue) supplies
+ 12
V DC
when you turn on the tuner.
• When your car has built-in FMIAM antenna in the rearlside
glass, connect the power antenna control lead (blue) or the
accessory power input lead (red) to the power terminal
01
the
existing antenna booster. For details, consult your dealer.
A power antenna without a relay box cannot be used with this
unit.
Memory hold connection
When the yellow power input lead
is
connected. power will
always be supplied to the memory circuit even when the ignition
switch
is
turned off.
Notes on speaker connection
Before connecting the speakers, turn the unit off.
Use speakers with an impedance
01
4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals 01 the right speakers with those 01 the
left speaker.
Do not connect the ground lead
01
this unit to the negative (-)
terminal 01 the speaker.
Do not attempt to connect the speakers in parallel.
Connect only passive speakers. Connecting active speakers
(With built-in amplifiers) to the speaker terminals may damage
the unit.
To avoid
a
malfunction, do not use the built-in speaker leads
installed in your car if the unit shares
a
common negative (-)
lead lor the right and left speakers.
Do not connect the unit's speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, "Failure"
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
Connection example
[gJ
Parts list
OJ
• This unit is designed for negative ground 12 V DC
operation only.
• Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power input leads only
after all other leads have been connected.
• Run all ground leads to a common ground
point.
• Be sure to insulate any loose unconnected leads with
electrical tape for safety.
• Do not cover the ventilation slots or heat sinks of the
unit.
• The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit's rating
must be higher than the sum of each component's fuse.
• When no car circuits are rated high enough, connect
the unit directly to the battery.
Note
Before installing, make sure that the catches on both sides
01
the bracket
CD
are bent inwards 2 mm (3/32 in).
If
the catches are
straight or bent outwards, the unit will not be installed securely
and may spring oul.
Catch
Be sure to install this unit in the dashboard of the car
as the rear side of the unit becomes hot during use.
Cautions
• The numbers in the list are keyed to those in the
instructions.
• The bracket
G)
and the protection collar
0
are
attached to the unit before shipping. Before mounting
the unit, use the release keys
®
to remove the bracket
G)
and the protection collar
0
from the unit. For
details, see "Removing the protection collar and the
bracket
<EI)"
on the reverse side of the sheet.
• Keep the release keys
®
for future use as they
are also necessary if you remove the unit from
your car.
Caution
Handle the bracket
G)
carefully to avoid injuring your
fingers.
x2
®
Rotary commander RM-X4S
Satellite de commande RM-X4S
Mando rotatorio RM-X4S
CDIMD changer
Changeur de CD/MD
Cambiador de CD/MD
Power amplifier
Amplificateur de puissance
Amplificador de potencia
x4
®
I I
Active subwoofer
Caisson de graves actif
Altavoz potenciador de
graves activo
Rear speaker
Haut-parleur arriare
Altavoz posterior
Front speaker
Haut-parleur avant
Altavoz frontal
®
Equipment used in illustrations (not supplied)
Appareils utilises dans les illustrations (non fournis)
Equipo utilizado en las i1ustraciones (no suministrado)
o
Notes
<III-A)
• Be sure to connect the ground lead before connecting the
amplifier.
• The alarm will only sound il the built-in amplifier
is
used.
Tip
<III-BoO)
For connecting two or more CD/MD changers. the source
selector XA-C40 (not supplied)
is
necessary.