Xerox DocuColor 40 Manuale delle impostazioni - Pagina 2
Sfoglia online o scarica il pdf Manuale delle impostazioni per Accessori per stampanti Xerox DocuColor 40. Xerox DocuColor 40 4. High speed paper-backed transparencies
Anche per Xerox DocuColor 40: Utilizzo del manuale (12 pagine), Manuale di riferimento (13 pagine), Manuale delle impostazioni (8 pagine), Manuale supplementare (17 pagine), Istruzioni per l'uso (1 pagine)
Stampa la pagina
Fiery X40 with version 1.0 Software, Digital Front End for DocuColor 40/30
Environmental Requirements
Operating Temperature
Humidity (non condensing)
Altitude (above sea level)
Server Specifications (minimum)
433 MHz Celeron Processor
256 MB RAM
CDROM
Mousitometer
ZIP Drive
8.4 GB IDE hard drive
10/100 BaseT Network capability (auto sensing)
Y2K compliant.
Note:
1.
Only 4GB out of 8.4 GB is used for printing and file storage.
Network Connectivity
Protocol Stack
Printing
Services
Novell IPX / SPX
PServer
Ethernet 802.2
Ethernet 802.3
Ethernet_II
Ethernet SNAP
Token Ring 802.2
(option)
Token Ring SNAP
(option)
TCP / IP
LPD/LPR
Ethernet_II
Token Ring SNAP
(option)
TCP / IP
SMB
Ethernet_II
Token Ring SNAP
(option)
TCP / IP
HTTP/IPP
Ethernet_II
TCP / IP
SPM/Port
Ethernet_II
9100
AppleTalk
PAP
Ethernet SNAP
(EtherTalk Phase 2
only)
Parallel Port
LPT1
N/A
The customer is responsible for supplying one network drop to enable the install.
Printing Specifications
PostScript
The Fiery X40 is a true Adobe PostScript 3 controller with PDF
native printing.
Print Speed / System Performance
The maximum print speed for the X40 system is limited by the
print speed of the DocuColor 30/40.
DocuColor 30/40 is a document printer; therefore in reverse
order printing the print engine will not cycle up until the entire job
is ready. This will impact First Copy Out Time (FCOT). The
copier may cycle down between each job depending on job
complexity.
Overall system performance ('Click to Clunk' time) is primarily
dependent upon the software applications and network
Terms and product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Customer Expectation Setting Document
Min.
Max.
o
o
o
o
50
F (10
C)
104
F (40
C)
5% RH
95% RH
0
10,000 ft.
(3,048 m)
Supported Frame
Platform
Types
Windows NT
4.0
Windows 95, 98
Windows 2000
Windows NT
4.0
Windows 95, 98
Windows 2000
SunOS 4.1.x
Windows NT
4.0
Windows 95, 98
Windows 2000
Windows 2000
Windows 2000
Windows NT
4.0
Macintosh
Windows NT
4.0
Windows 95,98
Windows 2000
December 1, 2000
environment being used. Rasterizing (RIP-ing) is only a small
fraction of Click to Clunk time.
Printing with custom software applications may produce
unexpected or unknown results.
The X40 DC 30/40 provides accurate billing of all color and
black & white images when programmed in black detection
mode. When black detection is enabled, productivity will be
affected by the detection of the black toner to process color
mix.
Maximum Image Sizes
The maximum image size from an application is limited to the
image size produced by DocuColor 30/40. The application and
the DocuColor 30/40 setup controls image position.
The maximum imageable area for the DocuColor 30/40 is as
follows:
Copier
17
Mode
Printer
17.13
Mode
IOT Firmware supported
Firmware version 4.6 and higher only. X40 will not
communicate with earlier versions.
ECT Compression
The Compression efficiency is dependent on file type and
complexity. Artifacts may be possible depending on the file
complexity. Compression can not be turned off.
Calibration
Mousitometer is the primary calibration method through
ColorWise Pro Tools.
The Mousitometer is supported with ColorWise Pro Tools/
Command workStation for Windows or with the FACI kit. Mac
is not supported.
For best results, calibrate on media that will be used for the
print job.
An optional X-Rite DTP32 densitometer is also available for
use with ColorWise Pro Tools.
Color monitor calibration is the responsibility of the customer.
Optimal print quality is achieved by using a densitometer. For
RGB emitting applications (PowerPoint, Word, and Excel), use
the DocuColor 30/40 calibration target. For CMYK applications
(Quark, Pagemaker) use the SWOP target.
Print Quality and Color Management
The appearance of the document displayed on the monitor
screen may not match the output print because the monitor
uses RGB color space parameters.
For imported RGB images, optimal color is achieved in the
EPS format. Other imported file formats may produce
unexpected results.
Separations Support
For the PC, only QuarkXPress & PageMaker should be used
for separations.
For the Mac, only QuarkXPress 4.0 or PageMaker version 6.5
can be used for separations.
The Combine Separation option is only supported for
QuarkXPress and PageMaker using four-pass color.
Inches
0.5% X 11.69
0.5%
432
0.5% X 11.69
435
0.5%
Millimeters
0.5% X 297
0.5%
0.5% X 297
0.5%
2