ARO GV08A-06S-7 Manuale dell'operatore - Pagina 11

Sfoglia online o scarica il pdf Manuale dell'operatore per Utensile elettrico ARO GV08A-06S-7. ARO GV08A-06S-7 12. Sanders/polishers

MAINTENANCE SECTION
Assembly of the Gear
l. If the Planet Gear Bearings (34) were removed, press
12. Using snap ring pliers, install the Arbor Bearing
Retainer (42) in the front end of the Gear Case.
13. Thread the Inner Wheel Flange (43) onto the Arbor.
2.
3.
4.
the new Bearings into the Arbor Planet Gears (33)
using a bearing inserting tool (see drawing TPD786)
that has a pilot and that contacts the outer radius of
the Bearings. Press against the stamped end of the
Bearing.
Smear some of the recommended grease on the
Bearings and teeth of the Planet Gears.
Using blocks or a ring on the table of an arbor press,
place the large shoulder of the Arbor (32), threaded
end down, on the blocks or the ring.
Position one of the assembled Arbor Planet Gears in
one of the machined Arbor openings, carefully
aligning the center of the Gear with the hole in the
shoulder of the Arbor, and press one of the Arbor
Planet Gear Shafts (35) into the Arbor and through the
Gear. Make certain both ends of the Shaft are below
the faces of the Arbor.
5.
6.
7.
Repeat the previous step with the second Planet Gear.
For Models GV08A-05S-7 and GV08A-06S-7,
grease the teeth of the Rotor Pinion (36) and insert it
into the center of the Arbor through the remaining
machined opening. Make certain the teeth of the
Rotor Pinion mesh with the teeth of the Planet Gears.
Install the remaining Arbor Planet Gear making
certain all gearing meshes and moves freely.
8.
9.
10.
11.
Do not press against the Rear Arbor Bearing.
Press the Rear Arbor Bearing (37) onto the shaft at
the unthreaded end of the Arbor.
Reposition the Arbor on the pressing table with the
threaded end up.
Position the Arbor Bearing Spacer (38) on the Arbor
and press the Front Arbor Bearing (39), shielded side
up, onto the Arbor.
Smear some grease on the internal spline of the Gear
Case (40) and insert the assembled Arbor, gearing end
first, into the unsplined end of the Gear Case. Make
certain the teeth of the Planet Gears mesh with the
teeth in the Gear Case.
14.
15.
16.
Using two 5/8-11 jam nuts on the end of the Arbor,
tighten the Inner Wheel Flange.
Lubricate and install the Exhaust Deflector Front
Seal (31) in the annular groove of the Gear Case.
Being careful not to cut the Seal, slide the smaller end
of the Exhaust Deflector (28) onto the Gear Case until
it butts against the shoulder of the Gear Case.
If the Exhaust Silencer (29) was removed, fold the
Silencer in half lengthwise and work it into the open
area between the Exhaust Deflector and the Gear
Case.
Assembly of the Tool
1.
2.
3.
4.
5.
6.
Grasping the handle of the Motor Housing in
copper-covered or leather-covered vise jaws with the
spline of the Rotor upward, place the Bearing
Housing Spacer (27) on the face of the Front Rotor
Bearing Housing.
Position the Gear Case and Exhaust Deflector over
the Motor Housing and while slowly rotating the
Arbor to align the Planet Gears with the spline of the
Rotor, screw the Gear Case onto the Motor Housing.
Make certain the Exhaust Deflector Rear Seal is not
cut while threading the Gear Case onto the Motor
Housing.
With a torque wrench on the flats on the Gear Case,
tighten the Gear Case to between 50 to 60 ft-lb (67.8
to 8 1.4 Nm) torque.
Install the Pad Mounting Spacers (44) on the Arbor.
Thread the Sanding Pad (46) and the Pad Mounting
nut onto the Arbor.
Spin the Sanding Pad by hand to make certain nothing
is binding, then remove the tool from the vise.
11