- ページ 6

インターホン・システム ASL INTERCOM PS 6379のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。ASL INTERCOM PS 6379 20 ページ。 Six channel loudspeaker master station pro series

ページを印刷する

6.0

FRONT PANEL CONTROLS & CONNECTOR

1 LISTEN LEVEL control knobs

These knobs preset the listen level for each channel

separately.

2 TALK buttons

These buttons allow you to talk to each channel

separately or simultaneously.

The large green LED is lit when the talk function for

that channel is activated. Should one talk to a

channel which is in IFB or PAGING mode by

pressing and holding that TALK button, the other lit

TALK buttons will switch off for as long as the IFB /

PAGING mode TALK button is pressed (for further

explanation of the Modes see section 9). To talk to

an IFB / PAGING channel and additionally to a

intercom channel, one should also press and hold

the TALK button of the intercom channel. If in IFB

mode and one would like to talk to all channels of

which the TALK LEDs are lit, than this can be

achieved by setting the corresponding, internal dip

switch "IFB and TALK" to 'on' (see 8.0 Internal

controls / Dip switches).

Latched switching:

When a TALK button is pressed shortly, the

microphone signal is sent to the chosen channel

and the TALK button latches electronically. When

pressed again, the Talk function will switch off.

` Momentary switching:

When holding a TALK button pressed while talking,

the microphone signal will be sent to the chosen

channel until the button is released. Then the talk

function will switch off automatically.

3 CALL buttons

These push buttons activate the call system, for

each channel separately.

A momentary push will sent a visual CALL signal to

all stations connected to the intercom channel and

the call LEDS will start flashing. When holding the

CALL buttons for 2 seconds the buzzer will be

activated, if there is no buzzer mute on this channel.

After the CALL button is released the LEDS will

continue to flash for further 2 seconds.

4 TALK to ALL

When the TALK to ALL button is pressed and held,

one will talk to all intercom channels simultaneously

and the green LEDs of all channels will light up –

except for the channels which are in IFB or PAGING

mode. To also include the channels which are in IFB

or PAGING mode, the dip switch IFB and TALK ALL

has to be switched to 'on' (see 8.0 Internal controls

/ Dip switches).

5 CALL ALL

When the CALL ALL button is pressed shortly a

visual call signal is sent to all channels and the red

LEDs will start flashing. When holding the CALL

buttons for 2 seconds the buzzer will be activated,

should no buzzer mute be activated for that

channel. After the CALL button is released the LEDs

will continue to flash for further 2 seconds. Channels

which are in IFB or PAGING mode do not receive

CALL signals.

6 MASTER VOLUME

This knob adjusts the volume of the speaker or

headset.

7 STAGE ANNOUNCE

This push button routes the microphone signal

directly to a line level output at the back of the unit.

The microphone signal will not be sent to the

intercom channel even if the TALK LEDs are lit. This

can be changed by setting the corresponding

internal dip switch (STAGE ANN. and TALK) to 'on'

(see section 8.0 Internal controls / Dip switches).

The Aux signal can also be routed to the STAGE

ANNOUNCE output by setting the corresponding

dip switch (AUX and STAGE ANN.) to 'on' (see

section 8.0). In EXTENDED Mode only the

microphone signal of the Master unit will be routed

to the STAGE ANNOUNCE output of the master.

This can be changed by setting the corresponding

dip switch (Stage announce mic. Select) to 'on'(see

section 8.0) in which case each unit will use its own

Stage Announce output and microphone.