- ページ 2

水ポンプ Aero Mist 50027-10のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。Aero Mist 50027-10 2 ページ。 150 psi booster pump kit/10 nozzle nylon tube system

ページを印刷する

Operation Overview

The Aero Mist 150 PSI Pump takes ordinary home water pressure which is normally

about 50-70 PSI for most homes and "boosts" it up to 150 PSI. The higher water pres-

sure created by the pump enhances mist cooling and heat absorption in two ways.

First, it produces a higher flow of water through the nozzle. More water being ex-

pelled from the nozzle means more cooling. Second, it creates a smaller finer mist

droplet which allows the droplet to evaporate more quickly. Better evaporation

means better cooling.

There are many applications for 150 PSI Booster Pump Kit by Aero Mist. Applications

include, Patio Cooling for Homes and Restaurants, Greenhouses, Humidification, Dust

control, Odor control and many more.

Caution, Warning and Safety Instructions:

Outdoor use ONLY! Not for use indoors

Install pump in a suitable place to prevent property damage in the event a leak

should occur.

Turn water off and disconnect power to the unit when not in use for extended

periods of time.

Plug pump into 110 volt GFCI protected outlet.

Do not place pump in or in damp or wet environments.

Feed system with potable cold water supply only. Do not connect pump to hot

water supply.

Do not expose pump to freezing temperatures. When winterizing disconnect

pump from power and water supply and store in a dry safe place. Make sure all

water is drained from the system to prevent damage in the event of a freeze.

Inlet

Outlet

INSTALLATION INSTRUCTIONS

Mount pump on wall in an outdoor location that is not in a not a damp or wet

environment.

Verify 110 Volt power supply is GFIC protected.

Verify water feed to pump location is potable cold water supply only.

Connect cold water feed to pump inlet and connect nylon tubing to pump outlet.

Proper installation of the mist line requires mounting the nylon tubing around the

bottom outside edge of the fascia, header or beam of the patio structure.

Properly installed mist lines create a curtain of mist around the open air sides of

the patio which cools the air as it enters the patio. Nozzles should be placed two

feet apart and should spray out into the open air. Do not install nozzles where

the spray may hit the patio, structure or surrounding objects as water damage

can occur. You will want to keep nozzles 12" to 18" inches away from columns,

structures and windows.

This system uses quick connect style fittings. Simply, cut the tubing at the desired

point and push and twist the fitting on to the end of the tubing. Check to see the

fitting is secure by gently pulling on the nylon tubing to make sure it is secure.

To release the tubing from the fitting you can us your hands or place a wrench

over the tubing where it goes into the fitting and press the collar of the fitting

back against the body of the fitting a pull the tubing free.

Before installing the nozzles in the system flush system by turning the pump on

and run water through the system without nozzles to expel any debris that may

have entered into the line during installation.

While the system is flushing, begin installing the nozzles. Hand tighten nozzles.

Start by installing the nozzles in the fittings closest to the pump first and work

your way back to the end of the mist line. Note: you will need the turn the pump

off when you get to the last 2-3 nozzles.

LIST OF ALL ENCLOSED PARTS

Item ID

Item Description

50027

Misting Pump 150 PSI 120 Volt

52014

Misting Nozzle 10/24 x .014

52505

Calcium Inhibitor Filter

52345

1/4"x3/8" Plastic Male Adapter

26102

Hose Adapter 3/4" x 3/8"

52340

1/4" Plastic Nozzle Union

56425-75

1/4" Nylon Tubing 75Ft Roll LP

52329

1/4" Push Lock End Plug

65186

Mini Tube Cutter

56374

Coated Clamp 1/4"

52602

Screw

52603

Plastic Anchor

Qty.