室内装飾品 AeroBed R111USBのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。AeroBed R111USB 2 ページ。

Thank you for joining the AeroBed

family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed

the comfort of an AeroBed

product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new AeroBed

others on your bed's proper use, maintenance and safety.

SAVE ThESE INSTrUCTIONS

rEAD AND FOLLOW ALL INSTrUCTIONS

BEFOrE USINg ThIS PrODUCT.

IMPOrTANT SAFETY

INFOrMATION AND WArNINgS

IMPORTANT

When using an electrical furnishing, basic precautions should always be followed, including

the following: Read all instructions before using (this furnishing).

Preparation of your AeroBed

product requires no tools. Use of tools may damage your bed.

This is an electrical product - not a toy. To avoid risk of fire, burns, injury, or shock:

• Always unplug this furnishing from the electrical outlet before cleaning or servicing.

• Use this product only for its intended use as described in these instructions. Do not use

attachments not recommended by the manufacturer.

• Never operate this product if it has a damaged cord or plug, if it is not working

properly, if it has been dropped or damaged, or dropped into water.

• Keep the cord away from heated surfaces.

• Never operate the product with the air openings blocked. Keep the air openings free of

lint, hair, and the like.

• Never drop or insert any object into any opening.

• Do not operate where aerosol (spray) products are being used or where oxygen is

being administered.

• Do not run cord under carpeting. Do not cover with throw rugs, runners or similar

coverings. Arrange cord away from traffic area and where it will not be tripped over.

• Product is for indoor use only. Do not use outdoors. For Household/Residential Use Only.

• This product has not been evaluated for flammability or cigarette ignition resistance.

• Use on flat surfaces only. Bed may tip over on uneven surfaces.

• Remove all sharp objects from area where bed will be set up and used. Do not use this

bed on abrasive surfaces or near pointed/sharp items or surfaces. Bed may puncture.

• Unplug product when not in use.

• Pump is not intended for continuous use. Pump may stop working or overheat if it is

used for extended periods of time.

• Do not use pump continuously for more than 10 minutes.

• To avoid excessive heat build-up in pump, allow pump to cool off for 30 minutes after

each 10 minutes of continuous use.

• Do not attempt to disassemble, repair, or service the pump. No serviceable parts are

contained inside. Contact The Coleman Company, Inc. at 3600 North Hydraulic, Wichita,

KS 67219, 1-800-835-3278 or TDD 1-316-832-8707 in the United States or Sunbeam

Corporation (Canada) Limited, DBA Jarden Consumer Solutions at 20B Hereford Street,

Brampton ON L6Y 0M1, 1-800-387-6161 in Canada for repair and service

center information.

SErVICINg OF DOUBLE-INSULATED PrODUCTS

In a double-insulated product, two systems of insulation are provided instead of grounding.

No grounding means is provided on a double-insulated product, nor is a means for grounding

to be added to the product. Servicing a double-insulated product requires extreme care and

knowledge of the system, and is to be done only by qualified service personnel. Replacement

parts for a double-insulated product must be identical to the parts they replace.

INSTRUCTION MANUAL

WARNING

INFLATION & ADJUSTMENTS

NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE

AIR LEAKS.

NOTE: PRESSURE CAN VARY DEPENDING ON ROOM TEMPERATURE AND CONSUMER WEIGHT.

1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.

2. Make certain the Quick Air Release Valve is closed. If the release valve is open, close it by

using 2 thumbs to push cover and snap into valve. Be careful to avoid pushing valve cover

to the right or left as it snaps into the valve opening.

This is the closed position.

Open Air Release Valve.

3. Remove the AC plug and cord from the plastic bag and

shrink wrap.

4. Plug into any standard polarized 120 Volt AC electrical outlet.

North American Electrical rating: 120 VAC 60 Hz 1.5 A.

(Note: 230 VAC product sold outside of North America). This

product has a polarized attachment plug (one blade is wider

than the other) as a safety feature. This plug will fit into a

polarized outlet only one way. If the plug does not fit fully in

the outlet, reverse the plug. If it still does not fit, contact a

qualified electrician. Never use with an extension cord unless

the plug can be fully inserted. Do not attempt to defeat this

safety feature.

5. On the Control Wand, press the UP arrow on the switch into the

"INFLATE" position to inflate your bed. Once bed has reached

desired firmness, return the switch to the off position "O".

6. Lie on your bed and use the Control Wand to adjust the firmness

to your desired level. For a firmer bed, press the UP arrow on the

switch into the "INFLATE" position. For a softer bed, press the

down arrow "ADJUST" until desired firmness level is attained.

7. Once desired firmness is reached, ensure the switch is returned

to the off position "O".

USB ChArgINg POrT

1. Your AeroBed

product includes a USB port built into the

pump for charging your personal device. Please adhere to the

following guidelines to ensure proper usage.

2. In order to charge your personal device

using the included USB port, the pump must

remain plugged into any standard polarized

120VoltAC electrical outlet throughout the

entire charging cycle.

3. For your convenience, directly below the

pump is a black mesh pocket that may be

used for storing your personal device throughout the charging cycle.

4. Once your device is fully charged, please disconnect the charging cable from the device

and from the USB port.

DEFLATION AND STOrAgE

1. To deflate your bed, open the Quick Release Valve and allow air to expel.

2. For the most compact storage, close the valve and use the Control Wand to press the

DOWN arrow on the switch into the "DEFLATE" position. After all the air is expelled from

the bed, return switch to the off position "O".

3. Roll or fold the AC cord and wand cord and secure it. Fold the sides of the bed into the

center along its length. Tightly roll and place the bed in the convenient carry bag or other

storage solution and store in a dry, clean location.

4. Store your bed in a clean, dry place at room temperature (above 50 °F/10 °C). Storing your

bed under 50 °F (10 °C) and over 100 °F (38 °C) may affect its performance and will not

be covered under warranty.

R111USB

product. You are about to enjoy

product. Always instruct and supervise

Close Valve Using 2 Thumbs.

INFLATE

DEFLATE

ADJUST