- ページ 8
オール・イン・ワン・プリンター Canon F-1のPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Canon F-1 12 ページ。 Booster t finder
Canon F-1 にも: 取扱説明書 (50 ページ), マニュアル (24 ページ), 取扱説明書 (13 ページ), クイック・スタート・マニュアル (4 ページ)
SPECIFICATIONS
8
Canon Battery Pack FN
Specifications
Structure:
Consists of a motor control c ircuit and a chamber for
loading twelve AA size batterie
s
with a battery
magazine.
Winding Speed: Three
changeable modes of H (5 frames
/sec.
),
L (3.5 frames /sec,) and S (single frame)
.
Operation:
Activated by the auxiliary motor drive
release
on
Bat-
tery Pack
FN
(vertical shot), shutter release button on the
camera or on top of
the
motor drive grip (horizontal shot),
Re-
mote Switch 3 or 60 using connecting cords, or with the
transmitter of Wireless Controller LC-1
.
Shutter Speed Coupling Range:
1/60
to
112000
in
H
mode
;
8
to
112000
in
L
or S
mode.
Frame Counting:
Frame counter of the AE Motor Drive FN
shows
the number
of unexposed frames
.
Functions indepen-
dently of camera 's frame counter.
Safety Circuit:
When
the
film
is
competely exposed or rewound
or if the battery power
fails,
film windinglrewinding
automat-
ically stops and the LED on AE Motor Drive FN flashes
.
Number of Film Rolls: In
normal temperature about
fifty
rolls of
36-exposure film using
H
mode.
Power Source: Twelve
AA size
batteries,
alkaline-manganese or
carbon zincs.
Size:
156.7mm(W) x 75.3mm(D) 36mm(H); (6-3/16" x
2-
11
/
16"
x
1- 1/
16")
Weight:
449g, 15-13/
16
ozs.
(including batteries)
e
Canon High Power Ni-Cd Pack FN
Specifications
Structure:
Consists of a motor control
c
ircuit and built-in Ni-Cd
battery.
Rechargeable
with Ni-Cd Ch arger MA /FN
.
Winding Speed:
Three operating speeds of H (5 frames /sec,)
,
L
(3.5 frames /sec.) and S (single frame).
Operation:
Activated by the auxiliary motor drive
release
on
High
Power Ni-Cd Pack FN (vertical shot), shutter release
button on the ca:mera or on top of the motor drive grip
(horizontal shot),
Remote
Switch 3 or 60
using
connecting
cords, or with the transmitter of Wireless Controller LC-1.
Shutter Speed Coupling Range:
1/60 to 1/2000 in H mode
;
8
to
112000
in
L
or S mode.
Frame Counting:
Frame counter of the AE Motor Drive FN
shows the number of unexposed frame
s.
Functions
indepen-
dently of camera 's frame counter.
.
Safety Circuit:
When
the
iilm is completely exposed or
rewound
or if the battery power
fails,
film winding /rewinding
automat-
ically stops and
the LED
on AE Motor Drive FN flashes
.
Number of Film Rolls: In
normal
temperature
about fifty rolls of
36-exposure
film
using H mode. In - 20°C temperature, about
twenty rolls of 36-exposure film
.
Power Source: Built-in Ni-Cd
battery,
14.4V.
Size:
156.7mm (W) x 75.3mm(D) x 36mm(H); (6-3/16" x 2-
15/16" x
1-7/16")
Weight:
469g,
16-9/
16 ozs.
e!)
Canon Ni-Cd Pack FN
Specifications
Structure:
Consists of a motor control circuit and built-in Ni-Cd
.
battery. Rechargeable with Ni-Cd Charger
MA/FN.
Winding Speed: Three
operating speeds of. H (4.5 frames/ sec.),
L(3 frames /sec.) and S (single frame)
.
Operation:
Activated by the auxiliary motor drive release on Ni-
Cd Pack FN (vertical shot), shutter release button on the
camera or on
top
of the motor drive grip (horizontal shot), Re
-
mote Switch 3 or 60
using
connecting cords, or with the
transmitter of
Wireless
Controller LC-1.
Shutter Speed Coupling Range:
1/60 to 1/2000 in
H
mode
;
8
to
112000
in L or S
mode.
Frame Counting:
Frame counter of the AE Motor
Drive
FN
shows the number of unexposed frame
s.
Functions
indepen-
dently of camera 's frame
counter.
Safety Circuit: When
the film is completely exposed or
rewound
or if the battery power fails, film winding
/
rewinding automat-
ically stops and
the LED
on AE Motor Drive FN flashes
.
Number of Film Rolls: In
normal temperature about thirty
rolls
of 36-exposure film
using H
mode.
Power Source: Built-in
Ni-Cd battery, 14.4V
Size: 156.7mm(W)
x 67 .8mm(D) x 26.6mm(H); (6-3/16" x
2-
11/16" x
1-1/16")
Weight:
212g, 7-1/2
ozs.
SG1 -A8
f)
Canon Film Chamber FN-100
_
Specifications
Type:
Bulk film chamber for use in conjunction with AE
Motor
Drive FN.
Attachment: By
exchange with camera's back cover.
Film Magazine:
Two magazines, one each for supply and take-
up, for exclusive use with Film Chamber FN-100.
Film Loading:
Film loading into Film Magazine FN-100 using
Film
Loader 250
in
a dark room.
Maximum Capacity:
100 frames of 35mm roll film.
Film Advance: Film
advance via motor drive with a provision for
synchronous film take -up.
Automatic Film Stop:
When the last frame passes over the
guide
roller,
an LED warning lamp of the motor drive lights
up.
Automatic Safety Circuit:
When the shutter button is
pressed,
the film chamber will not operate and the motor drive's wa
rn-
ing lamp lights up in the following cases:
1)
When there is no film in the film chamber or the film has
run
out;
2) When there is film loaded and the Open/Close knob on
the take-up side is at "OPEN ."
Frame Counter: Manually
set. subtractive type
Film Magazine Removal:
Via two eject levers, one inside each
magazine
chamber.
Shutter Release:
Four shutter buttons (one on film
chamber,
two
on motor drive plus camera's) each with a lock lever.
Back Cover Interlock:
Back locked with both OPEN /CLOSE
knobs at
"CLOSE"
or OPEN /CLOSE knob on magazine supply
side at "OPEN
."
Dimensions:
258.8(W) x 108.5(H)
x
72.3(D)mm
;
(10-3
/ 16"
x
4-
1/4"
x
2-7/8"
)
Weight:
641 g, 22-5 /8
OlS.
.(!)
Canon Data Back FN
Specifications
Attachment: By
exchange with camera's back cover.
Data Setting: Done
by three rotating
dials.
Data Setting Dials:
Right dial
:
32 digits and two blanks (0'0,0-31)
'
0 denotes a blank on film
.
Central Dial
:
39 chara cters and one blank (0,0-31, A-G)
Left dial: 39 characters and one blank (0
,
0 to 9,81 to
92),
Roman
numerals I
to
X and a to g)
.
Data Recording:
Data is automatically
recorded
in lower right-
hand
corner of frame and through the back of the film by a
built-in flash unit coupled to the shutter release
.
A separate
button
is
provided for manual data exposure.
Exposure (Light Intensity) Adjustment:
By setting dial to one
of three positions according to type of film.
Indicator Lamp:
Neon pilot
lamp
lights up to indicate Data Back
is ready for firing
.
Power Source:
One 6V alkaline -manganese (4LR44) good for
approximately 2,000 flashe
s.
Approximately 1,000 flashes
when using AE Power Winder FN for sequential shooting at 2
fps.
Main Switch:
ON-OFF,
when set
to OFF,
indicator
lamp
goes out
and no data will be recorded
.
Size:
103mm(W) x 14.3mm(D) x 49.2mm(H); (4" x
9/
16"
x
1-
7/8"
)
Weight:
166g, 6 ozs. (including battery)
0Canon Interval Timer TM-1 Quartz
Specifications
Connection:
By inserting the plug of the timer to the remote
control jack of one of the power packs for the AE Motor Drive
FN or to the remote jack of the AE Power Winder FN
.
Time Intervals:
Shooting in fixed intervals from one second to
30
minutes.
Settings for
1,
2,
5, 10, 15, 20,
30 and 40 second
s
and 1, 2,
5, 10,
20, and 30
minutes.
Switch Functions:
Power on /off of time setting and separate
on /offlrunning
lock
switch for activating shutter release
Battery Check: With
battery checklight LED on the timer
Power Source:
One 6V alkaline-manganese (4LR44)
Size:
38mm(W) x 19.5mm(D) x 94mm(H); (1-9/16" x
13/16"
x
3-
11/16")
Weight:
60g
,
2-1/8
OlS.
(including battery)