- ページ 2

ラベルメーカー Astro Machine AstroJet M1CのPDF クイック・リファレンスをオンラインで閲覧またはダウンロードできます。Astro Machine AstroJet M1C 2 ページ。
Astro Machine AstroJet M1C にも：クイック・スタート・マニュアル (6 ページ)

ページを印刷する

TOOLBOX SYSTEM STATUS MESSAGES

SYSTEM STATUS

SOURCE

X = Color.

One or more Ink

Tanks are out of ink.

Maintenance

procedure running.

Ink Tank is missing

or not recognized

(obtained from an

unauthorized

reseller).

If correct ink, check

contacts.

Printer is not level.

Printer's electronics

have detected that

the Print Engine is

too far out of level.

Tilt Sensor needs to

be recalibrated.

P2005 unplugged.

Mechanical Error

One of the Printer's

mechanical

components was not

properly registered

at the expected

position.

Mechanical failure or

Sensor failure.

(CONTINUED)

SOLUTION

Replace empty Ink Tank(s),

using the "Replace Ink

Tanks" command from EWS.

Verify that Ink Tanks are

seated firmly and latches are

fully closed.

Clear error using the

"Refresh Ink Levels"

command in the Toolbox or

just press PAPER button to

refresh ink levels and

continue printing.

No action required.

Insert missing Ink Tank or

pop the Ink Tank in and out

to improve connection.

Clear the error using the

"Refresh Ink Levels"

command in the Toolbox or

just press PAPER button to

refresh ink levels and

continue printing.

Make sure that Printer is

placed on a level surface.

Failure to do so may result in

severe ink mixing and cause

an inaccurate ink level

reading in the Ink Tanks.

If Printer was just powered

on, wait a few minutes; the

error may clear by itself.

Once the Tilt Level drops to

1.99 or less you can clear

the error using the "Clear

Error" feature in the Toolbox.

Make sure Printer is placed

on a sturdy, level worktable.

DO NOT move Printer while

power is on.

If the Tilt Level is 1.99 or less

PRINTHEAD_UNPRIMED

you can clear this error using

the "Clear Error" feature in

the M Series Toolbox.

Contact technical support to

have them check level and

possibly "Zero" the Tilt

Sensor.

Visually inspect the

component stated as a

"Reason" for failure.

Using the Scan Sensors

page in the Toolbox, perform

the toggle test on the Sensor

responsible for registration of

the failed mechanical

MECH_CANCELPAGE

component position.

Lifter Arm Sensor is dirty or

damaged, Lifter Motor Cable

is unplugged, operator's side

Lifting Arm is damaged, or

the Lifting Arm mechanism is

stuck.

Dual Pinch Valve Problem:

Check Sensor board

connector and flag/sensors

alignment. Check Valve

motor connector. Check

P2005 cable on MPCA.

At this point, this error may

represent an Ink Pump error,

since there is no return

signal from the pump and

therefore, a separate

message describing an Ink

Pump error.

SYSTEM STATUS

SOURCE

Data Cables

unplugged, dirty

Printhead contacts,

dirty PPCA contacts.

Service Station is

ejected, Service

Station position

sensors are

damaged or

malfunctioning.

Printhead Missing

and one or more of

the Ink Tanks are

missing, When this

error occurs, Multiple

EWS monitoring is

disabled.

Printhead Missing

and one or more of

the Ink Tanks are

missing. When this

error occurs, Multiple

EWS monitoring is

disabled.

No Printhead

installed or

Printhead not

making proper

connections.

J2001 cable

unplugged.

Printhead Latch is

open.

Printhead priming

process has failed.

Job was cancelled

by user pressing the

CANCEL button.

Job was interrupted

by "Clamshell" being

momentarily opened.

SOLUTION

Check data cables (P250,

P260), clean Printhead

contacts, and/or clean PPCA

contacts.

Check the Service Station

position. Using the Scan

Sensors page in the

Toolbox, perform the toggle

test on the two Sensors

responsible for registration of

the Service Station position.

Install Printhead.

Install Ink Tanks.

Install Printhead.

Install Ink Tanks.

If the Printer was just

powered on, wait a minute;

error may clear by itself.

Install Printhead Cartridge.

Remove and reinstall

Printhead.

Replace Printhead. Refer to

the appropriate sections in

this manual for removing and

installing the Printhead

Cartridge.

If Printer was just powered

on, wait a minute; error may

clear by itself.

Remove Printhead Cartridge,

wet the print nozzles using

deionized or distilled water

and reinstall the Printhead

Cartridge. Refer to the

appropriate sections in this

manual for removing and

installing the Printhead

Cartridge. If you continue to

have trouble priming the

Printhead; check for kinked

or pinched color tubes.

Wait until print job has

cleared from Printer. Then

manually clear job from

computer's print queue.

Then send new print job.

Check to be sure "Clamshell"

is securely latched, and then

press "Clear Error" button to

continue. If problem persists

contact service support.

630 Lively Blvd.

Elk Grove Village, IL 60007

Phone: (847) 364-6363

Fax: (847) 364 9898

www.astromachine.com

9/2014