- ページ 28

冷蔵庫 Electrolux 400 LTのPDF 設置および操作マニュアルをオンラインで閲覧またはダウンロードできます。Electrolux 400 LT 32 ページ。 Vertical refrigerators

ページを印刷する

C C A A U U T T I I O O N N

Do not clean the appliance with deter-

gents containing chlorine, solvent-based

cleaning products (e.g. trichloro-ethylene),

abrasive powders or agents, scouring

pads or sponges that could damage the

surfaces. Do not use organic solvent

substances or essential oils. These sub-

stances could damage the parts of the

appliance made from synthetic material.

C C A A U U T T I I O O N N

Do not use products (even if diluted)

containing chlorine (sodium hypochlorite,

hydrochloric or muriatic acid, etc.) to clean

the floor under the appliance.

J J . . 1 1 . . 3 3

P P r r e e c c a a u u t t i i o o n n s s i i n n c c a a s s e e o o f f l l o o n n g g i i d d l l e e p p e e r r i i o o d d s s

If the appliance is not going to be used for some time, take

the following precautions:

• disconnect the power supply;

• remove all food from the compartment and clean the inside

and accessories;

• clean the cabinet, going over all the stainless steel surfaces

vigorously with a rag moistened with paraffin oil to create a

protective film;

• leave the door open so that air can circulate inside,

preventing the formation of unpleasant odours.

• periodically air the premises.

After carrying out maintenance make sure the machine is

able to work safely and, in particular, that the protection and

safety devices are efficient.

J J . . 1 1 . . 4 4

Q Q u u i i c c k k t t r r o o u u b b l l e e s s h h o o o o t t i i n n g g g g u u i i d d e e

In some cases, faults can be eliminated easily and quickly by

following a brief troubleshooting guide:

The appliance does not switch on:

• make sure the plug is properly inserted in power socket.

• make sure the socket is powered.

• check (if present) the suitability of the fuse on the plug;

otherwise contact the assistance service to replace the

fuse, which must have the same characteristics as the

one being replaced.

The inside temperature is too high:

• check the thermostat setting.

• make sure there is no heat source near the appliance.

• make sure the door closes properly.

The appliance is too noisy:

• make sure the appliance is properly levelled. An unbal-

anced position can set off vibrations.

• make sure the appliance is not touching other equipment

or parts which could reverberate.

If the fault persists after carrying out the above checks,

contact the Customer Care Service, remembering to

specify:

A. the type of fault;

B. the appliance PNC (production number code);

C. the Ser. No. (appliance serial number).

J J . . 2 2

R R e e p p a a i i r r a a n n d d e e x x t t r r a a o o r r d d i i n n a a r r y y m m a a i i n n t t e e n n a a n n c c e e

J J . . 2 2 . . 1 1

R R e e v v e e r r s s i i n n g g o o p p e e n n i i n n g g o o f f m m o o d d e e l l s s w w i i t t h h f f u u l l l l y y i i n n s s u u l l a a t t e e d d

d d o o o o r r s s

The cabinets are normally supplied with right hinging. To

30°C

reverse opening, proceed as follows:

86°F

• turn off the main switch and disconnect the plug;

• remove the upper cover;

• arrange a support (not supplied) for placing at the bottom

part of the door;

• undo screws "H", remove the lower bracket "E" and fit it on

the left, in the holes provided;

• remove the temporary support and turn the door 180℃

• remove spiral bushing "F", move pin "L" from the slotted

hole on the left to that on the right. Fit spiral bushing "F" on it,

turned 180℃;

• remove upper bracket "G" and bushing "I";

• refit the door on the lower left hinge;

• refit bracket "G" on the left side of the cabinet and bushing

"I" on the left side of the door;

• adjust the door, ensuring perfect adherence of the magnetic

seal and refit the top cover.

J J . . 2 2 . . 2 2

R R e e v v e e r r s s i i n n g g o o p p e e n n i i n n g g o o f f m m o o d d e e l l s s w w i i t t h h g g l l a a s s s s d d o o o o r r a a n n d d

" " W W i i n n e e - - l l i i n n e e " " m m o o d d e e l l s s - - f f o o r r p p o o s s i i t t i i v v e e t t e e m m p p e e r r a a t t u u r r e e

a a p p p p l l i i a a n n c c e e s s o o n n l l y y - -

The cabinets are normally supplied with right hinging. To

reverse opening, carry out as follows:

• turn off the main switch and disconnect the plug;

•

remove the upper cover;

• arrange a support (not supplied) for placing at the bottom

part of the door;

• undo screws "H", remove the lower bracket "E" and fit it on

the left, in the holes provided;

NOTE!

The appliance PNC and serial number are essen-

tial for identifying the type of appliance and date of

manufacture.

NOTE!

Repair and extraordinary Maintenance have to be

carried out by specialised authorised personnel,

who can ask the manufacturer to supply a servicing

manual.