- ページ 8

電動工具 Bosch 1613のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Bosch 1613 28 ページ。 Plunge router
Bosch 1613 にも：取扱説明書 (28 ページ)

ページを印刷する

depth turret to progressively lower stops as

desired, until the final depth (lowest step or

flat) is reached.

Fine adjustment

The router is equipped with a true micrometer-

type fine adjustment mechanism, which can be

used in any plunge position and provides pre-

cise adjustment of the router bit position for

unmatched accuracy. When the tool is plunged

to the approximate position desired, this device

may be adjusted to precisely set the final cutter

position.

To use the fine adjustment, turn the fine adjust

knob 1 clockwise to lower the router bit or

counter-clockwise to raise it, as indicated by

the arrow molded into the top of the knob. To

allow precise settings, the indicator ring is

graduated in English and Metric increments,

and each line is equal to 1/10 mm or .004". The

indicator ring may be reset to zero without

moving the fine-adjust knob, to allow the user

to begin the adjustment from any reference

point desired.

The fine adjustment mechanism has a total

adjustment range of 5/8", which is indicated by

the two lines printed on back of the housing.

Whenever the fine adjustment is used, be cer-

tain that the index marker 17 is positioned

between these two lines to ensure that there will

be enough travel in the desired direction after

the router is plunged into position. Note that

when the router is plunged to maximum depth

or is fully retracted to the top of the posts, the

fine adjustment mechanism will not move the

motor further down or up, as the full extension

of the travel has been reached at these points.

Similarly, the fine adjustment cannot lower the

bit when the depth indicator rod is tightened

against the depth turret.

Direction of Feed

The router rotates in a clockwise direction, as

viewed from the top of the router. The correct

relationship between direction of router bit or

cutter rotation and router feed is shown below.

It is very important to move the router in the

proper direction or router bit chatter and rough

cutting will be the result. As an example, to

rout a decorative edge on the front of a table top,

you would move the router from left to right to

perform the operation, or counter-clockwise

BM 2610967928 1/97

around the workpiece. If you were cutting an

opening in the center of a panel, you would feed

the router in a clockwise direction, so that the

edge of the opening would be cut against the

rotation of the router bit as described, and have

a smooth finish. Whenever you are cutting

completely around a workpiece, it is advisable

to cut across the grain first, so any corner

tearout may be smoothed by cutting with the

grain on the second pass.

WORK

When routing or doing related work in wood

and plastics, the best finishes will result if the

depth of cut and feed rate are regulated to keep

the motor operating at high speed. Feed the

router at a moderate rate. Soft materials require

a faster feed rate than hard materials.

The router may stall if improperly used or

overloaded. Reduce the feed rate to prevent

possible damage to the tool. Always be sure the

collet nut is tightened securely before use.

Always use router bits with the shortest cutting

length necessary to produce the desired cut.

This will minimize router bit run-out and chat-

ter.

The router is equipped with an exclusive quick-

change templet guide mechanism, which firmly

grips the guides with a spring-loaded ring built

into the base. To in-

sert or change the

templet guide 24, re-

tract the templet

guide lock/release

lever 6. Align any

two of the four cut-

away tabs on the

templet guide to the

two cast-in bosses in

the templet guide re-

cess of the base.

CUTTER

DIRECTION

OF FEED

Rate of Feed

Templet Guides

12/7/98, 10:29 AM