- ページ 21

アンプ Bose PowerShare PS604AのPDF 設置および操作マニュアルをオンラインで閲覧またはダウンロードできます。Bose PowerShare PS604A 40 ページ。 Adaptable power amplifiers

ページを印刷する

pro.Bose.com

PS602P Rear Panel

Figure 5. PowerShare PS602P amplifier rear panel

q INPUT 1 & 2 – Balanced XLR/TRS and unbalanced RCA line-level input connectors. For each channel, use either balanced

or unbalanced input type, but not both simultaneously.

w USB – Connect the amplifier to a PC using a USB connection. This allows you to use the PC-based PowerShare Editor

software to configure the advanced features of the amplifier. The CONFIG DIP switch must be set to SOFTWARE to

configure the amplifer using the PowerShare Editor Software. See the Software Interface section for more details.

e CHANNEL 1 & 2 EQ – Each dial provides loudspeaker equalization presets per channel: DS 16, DS 40, DS 100, FS3B,

402, 802, MA12EX, RMU105, and RMU108. Use the Flat setting for FS3 Systems, or for loudspeakers that are not Bose

or that do not require EQ. When EQ is selected, the crossover and Vpeak and Vrms limiters for that loudspeaker are

automatically loaded. Use the PowerShare Editor Software to adjust any of these parameters - see the Software Interface

section for more details. In Hi-Z output mode, a 50 Hz high-pass filter (HPF) is automatically added to the Hi-Z selected

outputs. The loudspeaker EQ is applied after the 50 Hz HPF.

r MUTE – Contact closure connection where a short across the mute connector will mute all outputs. This is the Normally

Open (NO) default state. The mute polarity can be inverted to Normally Closed (NC), where an open across the mute

connector will mute all outputs, using the PowerShare Editor software. See the Software Interface section for more

details.

t DIP Switches – A bank of switches used to set the amplifier configuration. All switches set to the left position is the

standard configuration.

• AUTO STANDBY – If enabled (ON), the amplifier goes into lower-power mode after twenty minutes without an input

signal. If in lower-power mode and an audio signal is detected, the amplifier will automatically wake and amplify

audio within 1 second. The default position is OFF.

• GLOBAL OUT – Sets the output capability to 70V or 100V for all outputs that have their OUTPUT DIP switch set to

Hi Z. In 70V mode, a 100 Vpeak limiter is automatically loaded. In 100V mode, a 141 Vpeak limiter is automatically

loaded. These are maximum values that can be lowered using the PowerShare Editor software if necessary. See the

Software Interface section for more details.

• CONFIG – In REAR mode, only the rear panel EQ settings are required to configure the amplifier. In SOFTWARE

mode, the PowerShare Editor Software configures the amplifier, and the rear panel EQ switches are ignored. The

rest of the DIP switch settings are always independent of the PowerShare Editor software settings, as the software

does not interface with any other DIP switches. See the Software Interface section for more details.

• SENSITIVITY – Select 4 dBu or 12 dBu as the amplifier sensitivity for the XLR/TRS line-level inputs. The unbalanced

RCA input sensitivity is -10 dBV in the 4 dBu sensitivity setting, and -2 dBV in the 12 dBu sensitivity setting.

• OUTPUT 1 – Select 70/100V high impedance output (Hi Z) or 4-8 Ω low impedance output (Low Z) for OUTPUT 1.

• OUTPUT 2 – Select 70/100V high impedance output (Hi Z) or 4-8 Ω low impedance output (Low Z) for OUTPUT 2.

y OUTPUT 1 & 2 – NL4 and binding post outputs for each output. NL4 OUTPUT 1 combines both outputs, while NL4

OUTPUT 2 is only for OUTPUT 2. This gives access to both outputs on one NL4 four-conductor cable from NL4 OUTPUT

1, or two NL2 two-conductor cables can be connected to each output instead. Each channel can deliver up to 600 watts

regardless of load into 4 Ω, 8 Ω, 70V, or 100V. Outputs are not bridgeable.

u AC Inlet – Removing the AC cord when the amplifier is on is equivalent to powering down using the front panel power

switch, and is an acceptable power-down method.

Installation Guide

1. FLAT

2. DS16

MUTE

3. DS40

4. DS100

5. FS3B

6. 402

OFF

AUTO STANDBY

70V

100V

GLOBAL OUT

7. 802

REAR

SOFTWARE

CONFIG

8. MA12EX

4 dBu

12 dBu

SENSITIVITY

9. RMU105

Hi Z

Low Z

OUTPUT 1

0. RMU108

Hi Z

Low Z

OUTPUT 2

Front and Rear Panels

100-240V ~ 50/60Hz 700W MAX

PowerShare

PS602P

English 21