送信機 AIRTRONICS MX-3のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。AIRTRONICS MX-3 2 ページ。 3 channel computer radio system
ページを印刷する
TRANSMITTER BATTERY INSTALLATION
To Open slide Cover
Install Batteries
1.
Press down on the battery cover and slide
WARNING: Improper installation of transmitter batteries
in the direction of the arrow to remove.
can cause serious damage to your system.
2.
Install 8 pieces "AA" size alkaline batteries as
indicated on the battery tray. Make sure to match
the polarity (+ and -) as shown in the battery
compartment or the transmitter will not function.
3.
Install the battery cover in place and slide to close.
RECEIVER AND SERVO CONNECTIONS
Your MX-3 Computer R/C system receiver is NOT
Extend the receiver antenna to the full length. Failure
equipped with BEC circuitry. DO NOT use more
to do so will cause loss of control. Do not cut or bend the
than 6.0 volts to power the receiver. Anything higher
receiver antenna.
than 6.0 volts will burn-up or destroy your receiver.
Insulate the connectors with tape or use tie wraps to
Only use a 4.8~6.0 volt battery pack or a speed
avoid contact with metal car chassis.
controller that is designed to lower the voltage to
Please follow the model manufactures recommendations
the receiver. The following diagram shows a typical
for the correct installation of your radio system in your
connection for the servos and receiver.
car or boat.
Note that the receiver antenna should be located at
least 2" (50mm) away from any servo leads and
switches. In electric cars, we recommend that it be
at least 4" (100mm) from the electric motor.
B/DSC
B /
DSC
92836 75
FM
AA Dry Cell Battery Holder
Switch
Super Micro
3
3 CH. Receiver
2
1
Mechanical Speed Controller
#1
#2
#3
Steering
Throttle
AUX
B /
DSC
92836 75
FM
Super Micro
3
3 CH. Receiver
2
1
Electronic Speed Controller
TRIGGER POSITION ADJUSTMENT
To Close slide cover
A
B
Throttle Trigger Position Gauge
TROUBLESHOOTING GUIDE and WARNINGS
If your radio system does not operate properly, please
check the following items:
1. Make sure the batteries are properly installed and
fully charged. With alkaline batteries, make certain
the batteries are installed in the correct direction.
2. Check that both the transmitter and receiver power
switches are in the ON position.
3. Check the battery voltage by turning on the transmitter
and pushing both menu bottons at the same time
and releasing.
4. Make sure that the proper frequency crystals are
installed in both the transmitter and receiver.
5. Make sure all the receiver and servo connections
are tight.
!
CAUTION
When installing your MX-3 radio
system in your model, always
make sure to set your model on
a stand so the wheels are free
from any traction before turning
REGISTRATION NUMBER
on your radio and or connecting
To Battery
your motor for the first time.
The abbreviation, IC, before the registration number signifies that registration was performed based on a
Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not
To Motor
imply that Industry Canada approved the equipment.
Switch
To Battery
#2
To Motor
ESC
ESC
The Throttle Trigger can be adjusted to
give you a more natural feel of the throttle.
Throttle Trigger Set
Screw
To Adjust:
1. Loosen the Throttle Trigger set screw
by turning counter clock-wise.
2. Turning the adjustment screw clock-wise
will move the trigger out or in the (A)
direction.
3. Turning the adjustment screw counter
clock-wise will move the trigger in or
towards the (B) direction.
4. After adjustment is made, re-tighten
the Trigger Set Screw.
5. Total adjustment for the trigger is 10mm.
Throttle Trigger Adjustment screw
Do Not over tighten adjustment screw,
NOTE:
it may damage the adjuster and or
Trigger Set Screw must be
loosened before adjusting
the threads.
WARNINGS:
DO NOT OPERATE YOUR SYSTEM IF SOMEONE
ELSE IS ON YOUR FREQUENCE AT THE SAME TIME.
YOUR MODEL CAN CAUSE SERIOUS DAMAGE OR
INJURY SO PLEASE USE CAUTION AND COURTESY
AT ALL TIMES.
DO NOT EXPOSE THE RADIO SYSTEM TO WATER
OR EXCESSIVE MOISTURE.
PLEASE WATER PROOF THE RECEIVER AND SERVOS
BY PLACING THEM IN A WATER TIGHT RADIO BOX
WHEN OPERATING R/C BOAT MODELS.
IF YOU HAVE LITTLE OR NO EXPERIENCE OPERATING
R/C MODELS, WE STRONGLY RECOMMEND YOU SEEK
THE ASSISTANCE OF EXPERIENCED MODELERS OR
YOUR LOCAL HOBBY SHOP FOR GUIDANCE.
Get The Advantage
TH
D/R
EPA
ARC
H
MODEL
SUB-T
REV
BATT
MODEL
L
ST
L
R
MX-3
MENU
-
+
INC / DEC
DIGITAL CONTROL SYSTEM
3 Channel Computer
Radio System