- ページ 5

浄水器 Austin Springs AS-RO-75のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Austin Springs AS-RO-75 9 ページ。 Reverse osmosis water filter system

ページを印刷する

Installation Steps

Step 1: Connect the Water Feed Adapter

The Water Feed Adapter can convert to larger and smaller pipe threads. (Tip #4)

1 Turn off the cold-water supply by locating the valve

under the sink Confirm it is off by turning the sink faucet

onto cold No water should be running through

2 Disconnect the faucet connector pipe from the cold-

water supply Place a towel underneath to catch any

drips

3 Attach the Water Feed Adapter to the cold water supply

Re-connect the faucet connector pipe to the Water Feed

Adapter

1 –

4 Connect the

RED tubing to Water Feed Adapter

Step 2: Install Drinking Water Faucet

Faucet

Drain Input

Drain Output

Faucet Cuff

O-Ring

Counter

Split Washer

Spacer

Lock Washer

Lock Nut

Tube Insert

Collar

Brass Nut

Tubing

(See Tip #1)

7 –

1 Using the existing

hole or after having one drilled,

clean and dry the area

2 Slide the faucet cuff and o-ring over the faucet base

threads

3 Insert the faucet, threaded side down, into the hole

4 From under the sink, slide the split washer, spacer,

and lock washer on and firmly secure it with the lock

nut

1 –

5 Insert the black

tubing onto the drain input nipple

3 –

6 Insert the black

tubing onto the drain output

nipple

7 Assemble the compression fitting

(See Tip #2)

8 Insert the compression fitting into the threaded

end of faucet, tighten nut Once it is tightly in place,

gently pull tubing to confirm it is secure

Step 3: Install Drain Saddle

3 3

1 Choose a convenient spot for installing the drain saddle and tubing Installing on a horizontal

portion of the drain pipe will minimize dripping noise

1 –

2 Drill a

hole Paste the black sticky pad over it ensuring the holes align

3 Cut the end of the

the drain saddle by tightening the two screws and hex nuts Ensure that the hole in the drain

saddle is aligned with the hole that was drilled in the drain pipe

3 –

4 Connect the

Step 4: Install the Vertical Filters — Stages 3, 2 and 1

O-Ring

Step 5:

Install Tank Shut-off Valve

1 Use Teflon tape to wrap metal thread at

the top of the tank Wrap clockwise 10-

15 turns

2 Screw on Tank Shut-Off Valve and

tighten up by hand Do not over tighten

3 Connect the YELLOW tubing to the

Quick-Fitting of Tank Shut-Off Valve

3 –

Black tubing from the faucet drain output to the desired length Mount

BLACK tubing to the drain saddle

(See tip #1)

1 Inspect filter housing O-ring should be in the groove at the top

*Optional: Use Food-grade silicon jelly on O-ring for a better seal

2 Unwrap the filter cartridges; follow the color-coded stickers on the

packaging

3 Place each filter cartridge into its housing Make sure the center hole of

each filter is aligned onto the raised ring at the bottom of each housing

4 Screw each filter housing (with loaded cartridges) into the RO manifold

Ensure each cartridge is aligned to each of the center posts of the

RO manifold Twist clockwise by hand Use housing wrench to tighten

1 –

about

turn Overtightening may cause damage and leaks

5 Repeat these steps for each cartridge

in a certain direction — the end with the rubber washer faces up

NOTE:

the second stage must go