- ページ 15

リベット工具 Gage Bilt GB568のPDF オリジナル取扱説明書をオンラインで閲覧またはダウンロードできます。Gage Bilt GB568 20 ページ。 Installation tool
Gage Bilt GB568 にも：オリジナル取扱説明書 (16 ページ)

WARNING:

Disconnect tool from its air source before disassembly.

To inspect air cylinder bore, remove base cover (704125). Any further disassembly will require removal of the head cylinder assembly (752119) first.

For complete disassembly.

Remove base cover (704125).

Holding tool upright, remove four button-head cap screws (A-928). Lift head cylinder assembly (752119) from handle assembly

(722132) and set aside o'ring (S832) and gasket (704129).

Empty all hydraulic oil into an approved container and dispose of in accordance with the material safety datasheet.

Place piston rod wrench assembly (704149) down into top of power cylinder (722134) and into the hex of piston rod assembly (722133).

While holding the piston rod wrench assembly (704149), remove flexlock nut (400559) using a 7/16" socket / adjustable wrench.

Still holding piston rod wrench assembly (704149), remove air piston assembly (704121) using packing plug wrench assembly (704150),

by turning counterclockwise.

When air piston assembly (704121) is completely free from piston rod assembly (722133), tap or push on the piston rod wrench assembly

(704149) to eject air piston assembly (704121) from bottom of handle assembly (722132).

After removal of air piston assembly (704121), slide piston rod assembly (722133) back up to the end of its travel. Using packing plug

wrench assembly (704150) remove packing plug (704118).

With packing plug (704118) removed, power cylinder (722134) can be removed by pushing on power cylinder tool assembly (704151)

when inserted into top of power cylinder (722134).

To reassemble the handle assembly (722132).

Reverse the above procedure, being certain that all o'rings are properly lubricated before installation. Torque packing plug (704118)

to 45 foot lbs. (61 Nm).

Attach the seal guide (704152) to the piston rod assembly (722133) and tap the piston rod assembly (722133) through the packing plug

(704118).

Attach air piston assembly (704121) and flexlock nut (400559). Torque flexlock nut to 40 inch lbs. (4.52 Nm).

Attach air piston assembly (704121) to piston rod assembly (722133).

With the piston rod in the down position, fill oil passage on top of handle assembly (722132) with automatic transmission oil, Dexron® III or

equivalent. When looking at top of handle assembly (722132) the oil passage is the hole that has a counterbore for (S832) o'ring.

Replace gasket (704129) and o'ring (S832), just prior to replacing head cylinder assembly (752119). Torque all screws to manual

specifications. (See Filling and Bleeding procedure pg. 11) & (See torque specifications on pg. #10).

Remove pin (704244) and muffler (704146).

Insert valve extractor (S1178) into end of valve plug (704145) and pull it out.

Using the same procedure, pull out valve spool assembly (703142).

It should never be necessary to remove valve sleeve (703139) unless the ports in the valve sleeve (703139) are plugged from

contaminated air. If ports are plugged, use needle nose pliers to grasp end of spring (704141), turning clockwise and pulling to

dislodge from groove in casting. Valve spring installation tool assembly (704262) will facilitate the proper installation of the spring (704141).

Valve sleeve (703139) can be pulled out using valve sleeve removal tool assembly (704163).

GB722/568 INSTALATION TOOL

OVERHAUL

HANDLE

AIR VALVE

11/21 REV. 5/22