無停電電源装置 ADELSYSTEM CBI6024AのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。ADELSYSTEM CBI6024A 5 ページ。 Dc ups

ページを印刷する

DC Ups CBI60 "All in One"

CBI6012A and CBI6024A

Instruction Manual

Thank you for having chosen one of our products for your work.

We are certain that it will give the utmost satisfaction and be a notable

help on your job and application.

Product Description

New revolutionary product, with Ethernet on Board provided with protocol

connections: HTTPS, SNMPv3, ModBus TCP. The device also features

the ADELBus protocol for connecting other ADELSystem devices.

Thanks to "All In One" CBI series of DC-UPS, it will be possible to

optimize the power management of your system with one single,

extremely compact and cost-effective device, connected directly to the

mains. The available power is automatically distributed between load and

battery giving priority to the load. Battery can supply the load even with

mains so the output power to the load can be twice the nominal power if

required (Power Boost). When mains failure occurs, the load continues

to be supplied by the battery in backup mode. It is also possible to switch

on the device with no mains directly from battery. The "Battery Care"

algorithm performs rapid and automatic charging, continuous battery

charge optimization, flat batteries recovery and real time diagnosis during

installation and operation. Temperature compensation is possible by

connecting the temperature sensor probe. The real time auto-diagnostic

system monitors battery faults such as sulphated battery, shorted cells,

accidental reverse polarity connection or disconnection of the battery.

Each fault is signaled by a blink code of Diagnosis Led or via Modbus in

order to be easily detected and removed during the installation and after

sales. The continuous monitoring of battery efficiency reduces the risk of

battery damage and allows a safe operation in a permanent connection.

Predefined curves can be selected on the front panel to optimize the

charge of different battery types: Open Lead Acid, AGM and Gel Lead

Acid; Ni-Cd, Li-Ion are rechargeable using the same device. Charging

curves can be customized via Modbus. Output contacts are used to

signal both backup and fault conditions. A rugged casing with bracket for

DIN rail or Wall mounting.

Main Characteristics

•

Universal input voltage: single-phase 100–277 Vac

•

Load output:24 Vdc 2.5 A; 12 Vdc 5 A

•

Battery output:24 Vdc 2.5 A; 12 Vdc 5 A

•

"All In One" solution: power supply + battery charger + backup

module in one single device connected directly to the mains

•

Suited for different battery types: Open Lead Acid, Sealed

Lead Acid, AGM and Gel Lead Acid; Ni-Cd and Li-ion. 5-stage IUoU

(Recovery, Bulk, Absorption, Float, Refresh Battery) plus Recovery

stage for deeply discharged batteries

•

Automatic diagnosis of battery status and battery Life Test

function (Battery Care)

•

Switching technology with high efficiency

•

Protected against short circuit, overload and inverted polarity

Via Luigi Barchi 9/B – Reggio Emilia 42124 – Italy

Tel. +39 0522 345518 – Fax +39 0522 345551 –

•

Solid state output contact for signaling Low Battery or Battery

Replacement and Fault system.

•

IP20 protection degree

•

Space saving on DIN rail

Safety and warning notes

To safely operate this Device please read and follow all

instructions carefully before attempting to unpack, install,

or operate.

WARNING – Explosion Hazard: do not disconnect

equipment unless power has been switched off or the area

is known to be non-hazardous.

WARNING – Explosion Hazard. Replacement of components may impair

suitability for class I, Division 2.

WARNING – Switch off the system before connecting the module. Never

work on the machine when it is live. The device must be installed

according to EN61010 or EN62368-1. The device must have a suitable

isolating facility outside the power supply unit, via which it can be

switched to idle. Danger of fatal injury!

WARNING – The device is equipped whit an internal fuse. If the internal

fuse blows up (fails opens), it is most probable that there is a fault in the

device. If this failure occurs, the device must be returned to the factory.

How to Install

Mounting

Fig. 1 – Mounting of the CBI60

Din Rail or Panel Mounting

Fig. 1 shows how to install the CBI60. It is possible to mount the device

on DIN rail or on a panel and fix it by 4 screws 2.9x8-16. There is no limit

for the panel thickness.

Device Connection (Fig.2)

Fig. 2 –Connection terminal

Reference

Description

Battery

Load

System fault – Rectifier alarm

Mains – Backup

Mains – Backup LED

Battery fault – System fault LED

Diagnosis LED

Configuration – Start from Battery

Input Vac

Aux1: RJtemp – DPY353

Start from Battery: (close to negative load)

www.adelsystem.com

Instruction Manual CBI60_4

Page 1