- ページ 15

セキュリティシステム ADEMCO LYNXのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。ADEMCO LYNX 17 ページ。
ADEMCO LYNX にも： クイック・スタート・マニュアル (8 ページ), システムマニュアル (14 ページ)

ページを印刷する
ADEMCO LYNX ユーザーマニュアル
81
ZONE LISTS FOR OUTPUT DEVICES
Fill in the required data on the worksheet below and follow the procedure in the installation manual as you enter the data
during the displays and prompts that appear in sequence.
Note:
Record desired zone numbers below. More or fewer boxes than shown may be needed, since any list may
include any or all of system's zone numbers.
Zone List 1: Started or stopped by zone numbers (enter 00 to end entries).
[28] [32]
Zone List 2: Started or stopped by zone numbers (enter 00 to end entries).
[29] [33]
Zone List 3: Started or stopped by zone numbers AND/OR assignment of Chime zones (enter 00 to end entries)
[02] [03]
ENROLL AS "UR" OR "RF"
ENROLL AS "UR" OR "RF"
LOOP 3
NOTE: You must enroll loop 4 on the 5801, 5804 and 5804BD transmitters, regardless of whether the other loops
are being used.
SPECIAL MESSAGES
EE = DATA ENTRY ERROR (invalid field number entered while programming; re-enter valid field number).
FC = Communication Failure
EA = Exit Alarm
CA = Cancel Alarm
CC = Modem Communication (system is in communication with the central station)
After powering up, AC, dI (disabled) will be displayed after approximately 4 seconds. This will revert to the Real-
time Clock in approximately 1 minute. To bypass this delay, press: [#] + [0].
5800 SERIES LOOP NUMBERS
LOOP 3
LOOP 2
LOOP 1
LOOP 4
YOU MUST
ENROLL THIS
BUTTON
5 8 0 2 / 5 8 0 2 C P
ENROLL AS "BR"
5 8 0 1
YOU MUST
ENROLL THIS
BUTTON
LOOP 4
LOOP
1
5 8 0 2 M N
5 8 0 4
ENROLL AS "BR"
LOOP 2
YOU MUST
ENROLL THIS
BUTTON
LOOP 4
LOOP 1
5 8 0 6 / 5 8 0 7 / 5 8 0 8
(5806 SHOWN)
•
• •
• • •
SET
ENROLL AS "RF"
• •
• •
• •
•
HOUSE
•
CODE
5 8 0 4 B D
ENROLL AS "BR"
LOOP
LOOP
2
(REED)
(REED)
LOOP 1
(TERMINALS)
LOOP
1
ALTERNATE
5 8 1 6
ENROLL AS "RF"
FOR LOOP 2
LOOP
1
(PRIMARY)
LOOP 3
2
(AUX. CENTER)
LOOP 2
3
LOOP 1
(AUX. RIGHT)
5 8 1 7
ENROLL AS "RF"
LOOP
2
(REED)
LOOP 1
(TERMINALS)
5 8 1 9
ENROLL AS "RF"
LOOP 3
(TERMINALS)
LOOP
1
LOOP
1
(MOTION)
5 8 4 9
ENROLL AS "RF"
15 –
–
2
LOOP 1
(TERMINALS)
5 8 1 6 M N
POSITION
ENROLL AS "RF"
LOOP
1
5 8 1 8
ENROLL AS "RF"
5 8 2 7
SET HOUSE CODE
5 8 2 7 B D
SET HOUSE CODE
LOOP
1
(MOTION)
5 8 9 0
ENROLL AS "RF"
.etc.
.etc.
.etc.