- ページ 9

セキュリティシステム ADEMCO VISTA 5140XMのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。ADEMCO VISTA 5140XM 15 ページ。 Commercial fire & burglary alarm system

ページを印刷する

BURGLARY ALARM SYSTEM OPERATION

(IF INSTALLED)

DISARMING THE SYSTEM

AND SILENCING BURGLARY ALARMS

(FOR AWAY, STAY, INSTANT, AND MAXIMUM ARMING)

PROCEDURE

1. Enter security code and press OFF [1].

The Ready message will be displayed

and the console will beep once to

confirm that the system is disarmed,

unless an alarm has occurred.

2. If an alarm has occurred, note the zone

descriptor displayed and repeat step 1

to restore the Ready message display.

If the message will not display, go to

the displayed protection zone and

remedy the fault (close windows, etc.).

If the fault cannot be remedied, notify

the alarm agency.

DURESS CODE

(WHEN FORCED TO DISARM/ARM UNDER THREAT)

Enter the pre-assigned duress code. The

system will disarm (or arm), but can silently

notify the central station of your situation, if

that service has been provided.

– 16 –

RESULT

Any alarm sounders will be silenced;

ALARM and zone descriptor (if displayed)

will clear only when the open sensor is

closed.

A fire alarm is indicated by a display of

both FIRE and the zone descriptor on the

Console. These will clear only when the

fire zone is again intact.

S e e

" S U M M A R Y

O F

A U D I B L E

NOTIFICATION" section for information

which will enable you to distinguish

between FIRE and BURGLARY alarm

sounds.

IMPORTANT

• This code is useful only when connected

to a central station.

BURGLARY ALARM SYSTEM OPERATION

(IF INSTALLED)

CHIME MODE

(THIS FEATURE IS FUNCTIONAL ONLY WHEN THE BURGLARY SYSTEM IS

DISARMED)

Your system can be set to alert you to the

opening of a door or window while it is

disarmed by using CHIME mode. When

activated, three tones will sound at the

Console whenever a door or window is

opened, and the Not Ready message will

be displayed. Pressing the READY [*] key

will display the open protection points.

Note that Chime mode can be activated

only when the system is Disarmed.

TESTING THE BURGLARY SYSTEM

(TO BE CONDUCTED WEEKLY)

This feature can be used by your installer or by the master or manager user. Use this

test to check that sensors on all burglary and non-fire emergency zones are

operating properly. Note: If you fault a fire zone, you will cause a fire alarm!

1. Disarm the system.

2. Enter a master or manager code and

press the TEST [5] key.

3. The external burglary sounders will

sound for 3 seconds to indicate that the

test has started.

The console will

display "BURGLARY WALK TEST IN

PROGRESS" and will beep every 15

seconds while the test remains active.

4. Open and close each protected door

and window in turn.

Each action

should produce three beeps from the

Console, and the identification of each

protection point should appear on the

display.

To turn Chime Mode on, enter the

security code and press the CHIME [9]

key. The CHIME MODE ON message will

appear for about two seconds then

disappear. To display this message again

(to determine whether chime mode is on or

off), simply press and hold down the

CHIME key for 5 seconds.

To turn Chime Mode off, enter the

security code and press the CHIME [9] key

again. The C HIME MODE OFF message

will appear for about two seconds then

disappear.

5. Walk in front of any interior motion

detectors (if used). Listen for three

beeps

as the detector

senses

movement. The identification of the

detector should appear when it is

activated.

6. When all protection points have been

checked, there should be no zone

identification numbers displayed. If a

problem is experienced with any

protection point (no confirming beeps,

no display), CALL FOR SERVICE

IMMEDIATELY.

7. Turn off Burglary Walk Test mode by

entering any security code and

pressing the OFF [1] key.

– 17 –