送信機 ADEMCO 5879のPDF インストールとセットアップマニュアルをオンラインで閲覧またはダウンロードできます。ADEMCO 5879 3 ページ。 Holdup switch / transmitter
ページを印刷するGENERAL INFORMATION
The 5869 Holdup Switch/Transmitter is a finger-operated
RF transmitting device used for activating a holdup signal
at the security system control, and/or any other security
application. The 5869 is typically mounted under a counter
or money draw for inconspicuous operation.
transmitter is activated, it sends an RF signal to the control
panel, which then sends a burglary alarm to the central
station.
Once the 5869 trigger (Figure 1) is activated, the supplied
reset key K4563 must be used to reset the device. The 5869
also contain tamper switches that are activated either when
the cover is removed, or when the unit is forcibly removed
from its installation location.
The 5869 has a permanent serial number assigned during
manufacture used for enrolling the 5869 with the security
system control panel.
respective Security System Control Panel Installation and
Setup Guide.
RESET
KEY
COVER
ATTACH
HOLE
MOUNTING
HOLE
(TYP.)
TRIGGER
+
3V
BREAKAWAY
LITHIUM
BATTERY
+
COVER
TAMPER
SWITCH
ANTENNA
COVER
ATTACH
HOLE
Figure 1. 5869 Holdup Switch/Transmitter Details
INSTALLATION AND SETUP GUIDE
When the
To enroll the 5869, refer to the
COVER
TAMPER
SCREW
No. 6X3/4
COVER
SCREW (2)
No. 6X1/2
MOUNTING
Mount the 5869 under a counter or money drawer for easy
access by the cashier. Refer to the figure and steps that
follow for typical mounting installation.
Before mounting the 5869 permanently, perform Go/No Go
tests to verify adequate transmitter signal strength at desired
mounting location (refer to the Security System Control
Panel Installation and Setup Guide).
1.
Install the battery into the battery holder observing
correct polarity as shown in Figure 1.
2.
Position the case to the desired location and install one
No. 6 x ¾ screw (supplied) at the breakaway tamper
release hole as shown in Figure 2 .
3.
Secure the cover to the case with the two screws (No 6 x
1/2) as shown in Figure 2.
IMPORTANT: To prevent damage to the case, do not
over tighten the cover screws.
4.
Secure the case with the cover to its mounting location
using the two screws (No. 6 x 2) supplied as shown in
Figure 2.
PROGRAMMING
The
programmed as a 24-hour silent zone type. Refer to the
Security System Control Panel Installation and Setup
Guide for programming instructions.
NOTES:
•
During programming of the control panel, the 5869
Holdup Switch/Transmitter should be treated as "RF"
(i.e., supervised RF) Type.
•
The 5869 is one closed input loop zone (loop 1).
COVER
SCREW (2)
BATTERY INSTALLATION/REPLACEMENT
No. 6X1/2
Risk of fire, explosion, and burns. Do not recharge, disas-
semble, heat above 100°C, or incinerate. Dispose of used
batteries promptly and properly. Keep away from children.
IMPORTANT: The case will be held in place by the
tamper release tab once the cover and mounting screws
are removed. Exercise caution not to jar the case while
replacing the battery, possibly breaking the Tamper
MOUNTING
SCREW (2)
breakaway tab.
No. 6X2
1.
Remove the screws securing the 5869 cover and case to
its mounting location.
NOTE:
attempting to remove or install the battery.
2.
Remove faulty battery and dispose of properly.
3.
Observing correct polarity, insert the battery into the
5869-002-V1
battery holder as shown in Figure 2.
4.
Re-install screws to secure cover and case as shown in
Figure 2.
Holdup Switch/Transmitter
5869
Holdup
Switch/Transmitter
BATTERY CAUTION:
Use care not to bend the antenna while
K5299V1 3/03
5869
should
be