- ページ 3

煙警報器 ADEMCO 5808のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。ADEMCO 5808 4 ページ。 Photoelectronic smoke/heat detector with built-in wireless transmitter
ADEMCO 5808 にも：インストレーション・インストラクション (5 ページ)

ページを印刷する

ment. They can supply more detailed information about making your home

as free from fire hazards as possible and about planning for escape in case

of fire.

MOUNTING

First, determine the best location for the smoke detector; a location that

provides strong wireless transmission paths and proper smoke detec-

tion. A GOOD TRANSMISSION PATH MUST BE ESTABLISHED

FROM THE PROPOSED MOUNTING LOCATION BEFORE PERMA-

NENTLY INSTALLING THE DETECTOR. To check, perform the test

described in the TESTING TRANSMITTER SIGNAL section of this

manual. To mount the detector:

1. Once a suitable location has been determined, install the mounting

bracket on the ceiling or on the wall (if local ordinances permit). Use

the two screws and anchors provided.

2. Prior to mounting the detector to the mounting bracket, the system

must "enroll" the detector's ID. See the PROGRAMMING section for

the steps to follow.

3. Turn the detector in a clockwise direction in the mounting bracket

until it clicks into place.

4. Test the detector immediately after completing the installation (as

described in the TESTING section of this manual) and refer to the QED

control system's instructions for additional information concerning the

use of wireless smoke detectors.

TAMPER SLOT

(DEPRESS TAB

TO REMOVE

DETECTOR)

Figure 6. Detector Mounting Bracket

Figure 7. Mount Detector Across Ceiling Panel Support

DO NOT attach the detector to removable ceiling panels. Attach the

detector across panel support as shown in Figure 7.

TAMPER PROTECTION

This detector has a built-in tamper switch that will cause a CHECK signal

to be displayed at the console of the detector if it is removed from its

installation bracket. The mounting bracket can also be made tamperproof

by breaking off the smaller tab at the scribed line (see Figure 6), thus

preventing removal of the detector without a tool. To remove the

detector, use a small screwdriver to depress the tamperproof tab and

turn the detector counterclockwise.

TESTING

NOTE:

Before testing, notify the proper authorities that the smoke

detector system is undergoing maintenance and will tempo-

rarily be out of service. Disable the zone or system undergoing

maintenance to prevent unwanted alarms.

Detectors must be tested after installation and following periodic main-

tenance. The 5808 may be tested as follows:

A. TEST SWITCH

1. A recessed test switch is located on the detector housing.

2. Push and hold the recessed test switch with a 0.1" maximum

AD300-00-00

TAMPER RESISTANT TAB

(CUT OFF SMALL TAB TO

ACTIVATE TAMPER PROOF

FEATURE)

BRACKET INDICATES

POSITION OF LED WHEN

DETECTOR IS INSTALLED

A78-2333-03

A78-2620-00

CAUTION

diameter tool (an allen wrench or small screwdriver.)

3. The LED on the detector should blink once per second and the horn

should sound within 3 seconds.

B. TEST MODULE (Model No. MOD400R)

The MOD400R test module can be used with a DMM or analog

voltmeter to check the detector sensitivity as described in the test

module's manual.

C. SMOKE ENTRY TEST

Hold a smoldering punk stick or cotton wick at the side of the detector

and gently blow smoke through the detector until the unit alarms.

D. DIRECT HEAT METHOD (Hair dryer of 1000-1500 watts)

Direct the heat toward either side thermistor. Be sure to hold the heat

source about 12 inches from the detector to avoid damage to the

plastic. The detector will reset only after it has time to cool.

Smoke detection testing is recommended for verifying system protection

capability.

A detector that fails to activate with any of these tests should first be

cleaned as outlined in this manual's MAINTENANCE section. If the

detector still fails to activate, return for repair.

Notify the proper authorities that the system is back on line.

TESTING TRANSMITTER SIGNAL

NOTE: Remove battery tab before installation.

This test should be performed before installation to determine a strong

communication path with the QED control panel and after installation is

complete. Also, the owner/user should test the unit at least weekly.

1. Activate the wireless system's TEST mode from the console.

2. Depress and hold the smoke detector's TEST switch and the detector

should immediately transmit an alarm signal to the QED control panel.

The built-in horn will start to sound about 2.5 seconds after depressing

the button.

3. The wireless system's console should emit at least 3 audible sounds

when the alarm transmission is received and will display the transmit-

ting detector's ID number.

4. When the console has received the test signal, release the TEST

switch. The horn will immediately stop and a few seconds later the

detector's ID number will clear from the console display.

5. If the console does not respond as noted, check the polarity of the

batteries and be sure they are fresh. If this is an initial installation, try

moving the detector to another location that provides proper recep-

tion. Also be sure that the detector's ID has been "enrolled" by the QED

control panel (see PROGRAMMING). Then, repeat the test.

6. Turn off the system's TEST mode from the console (security code +

OFF).

MAINTENANCE

Figure 8. Removal of Cover and Screen for Cleaning

ARROW IS ALIGNED

WITH COVER REMOVAL

SLOT WHEN COVER

IS IN POSITION.

REPLACEMENT SCREEN,

ORDER PART NO. RS23

COVER

REMOVAL SLOT

A78-2335-01

I56-918-06