- ページ 8

スイミングプールクリーナー 8STREME TP2222のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。8STREME TP2222 9 ページ。 Above ground automatic swimming pool cleaner

ページを印刷する

PROBLEM

The robot moves in one direction

- An object blocks the rollers, the wheels of the robot

or interfering with the movement of the robot.

The robot does not move and the filtration pump

-The robot is not connected to a power source.

does not work either. The robot doesn't work any

-Power is

off .

longer.

The pump runs but the robot does not move. The

- No/ not enough power is transmitted to the robot

robot turns on but stays on the spot.

- An object blocl < s the rollers,.

- Possi6ility of motor problem

- Connection of the floating cable

The robot stops after a few minutes

- Possibility of fault of the floating cable

- Possibility of motor leakage

- The robot is too heal(Y

The robot moves slower than before

- The flow is not sufficient

- Cables connections

CAUSE(S)

SOLUTION(S)

- Unplug power supply and take robot out of water.

Open the cleaner to inspect the cleaner.

- Clieck that there are no foreign objects in the

impellers.

- Check that there are no foreign object blocking the

rollers located below the cleaner.

- Check that the i:1ower source is active by plugging

another device into the power outlet.

- Check that the power supply is turned on.

- Check all connections of the robot to the power

source.

- Check that there are no foreign objects in the

impellers.

- Unplug the power and take out the robot in the

water. Open the cover of the basket and remove the

basket.

- Check that there are no foreign objects in the

impellers.

- Check that there are no foreign object blocking the

rollers located below the cleaner.

- Contact the After-sales Service

- Check the connection of the floating cable.

Disconnect and reconnect as needea.

- Check the status of the connectors at the ends of

your cables (damaged, rusted, etc.)

- Check the basket and clean it if necessary.

- Check that there are no foreign objects in the

impellers.

- Check that there are no foreign object blocking the

rollers located below the cleaner.

- Check the status of the connectors at the ends of

your cables (damaged, rusted, etc.)

SYMPTOM

REASON(S)

No LED lit on the transformer

- No power at electrical socket

- Transformer (power supply) defective

The blue LED on the "No-Twist" floating swivel does

- Bad connection between the transformer and

not light up ( light C of Chapter S).

the No-Twist floating device.

- Possibility of No-Twist floating swivel problem

- You did not press the

the transformer to activate the cleaner.

The blue light on the "No-Twist" floating swivel is on

- Electrical connection problem at the No-Twist

but the red LED light does not (light E of Chapter S).

swivel

- Possibility of No-Twist floating swivel problem

- Bad connection between the No-Twist floating

The blue light on the No-Twist Floatin_g device is on

device and the cleaner

but the cleaner does not work ( light C of Chapter 5 ).

- Possibility of No-Twist floating device problem

- Possibility of motor problem.

Please contact www.8streme.com if you have any other questions.

SOLUTION(S)

- Check all connections ( chapter 4 ).

- If moisture is present on the plugs, let them

dry before reconnecting them.

- Check your electrical outlet

- Replace transformer (power supply)

- Contact customer service at 201 465 4200 ext 2

- Turn ON the cleaner by gressing the ON/ OFF

switch located on top of the transformer.

- Check all the connections of the cables between

the transformer and the No-Twist floating device.

on/off

switch located on

- Contact the After-sales Service 201 465 4220

- Check the status of the connectors at the ends of

the No-Twist floating swivel (damaged, rusted, etc.)

- Contact our Customer Service. 201 465 4220 ext 2

- Check if the connection at the "No-twist" float

outlet, blue outlet "Pool Cleaner" is correct and

waterproof.

- If the blue light C is on, you should also have a red

light on at tne float outlet (light E in Chapter 8).

If this is not the case, it is likely that the swivel is

defective.

- If both blue and red lights are on but the robot does

not work, please contact your dealer or our after-

sales service at [email protected] or call 201

465 4220 ext 2