セキュリティセンサー Autonics PSAN SeriesのPDF 製品マニュアルをオンラインで閲覧またはダウンロードできます。Autonics PSAN Series 7 ページ。 Display type pressure sensors
Autonics PSAN Series にも： マニュアル (2 ページ), 製品マニュアル (6 ページ), マニュアル (13 ページ)
ページを印刷する
TCD210185AC
Display Type
Pressure Sensors
PSAN Series
PRODUCT MANUAL
For your safety, read and follow the considerations written in the instruction
manual, other manuals and Autonics website.
The specifications, dimensions, etc are subject to change without notice for product
improvement Some models may be discontinued without notice.
Features
• Pressure measurement of any gas, liquid or oil (except substances which may corrode
stainless steel 304/316L)
• Auto shift function: with change in the original pressure, the external input adjusts the
determined level to match the change in pressure (only available in models with auto
shift/hold function)
• Hold function: hold current display value or control output
• Forced output control mode for device testing and maintenance
• One-touch connector type for easy wiring and maintenance
• Zero-point adjustment function, peak value monitoring function, chattering
prevention function
ᜢ ᜫ
Safety Considerations
• Observe all 'Safety Considerations' for safe and proper operation to avoid hazards.
• symbol indicates caution due to special circumstances in which hazards may occur.
Warning
Failure to follow instructions may result in serious injury or death.
01. Fail-safe device must be installed when using the unit with machinery that
may cause serious injury or substantial economic loss. (e.g. nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion
apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, economic loss or fire.
02. Do not use the unit in the place where flammable/explosive/corrosive gas,
humidity, direct sunlight, radiant heat, vibration, impact, or salinity may be
present.
Failure to follow this instruction may result in explosion or fire.
03. Install on a device panel or to a pressure port directly to use.
Failure to follow this instruction may result in fire.
04. Do not connect, repair, or inspect the unit while connected to a power
source.
Failure to follow this instruction may result in fire.
05. Check 'Connections' before wiring.
Failure to follow this instruction may result in fire.
06. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire or electric shock.
Caution
Failure to follow instructions may result in injury or product damage.
01. Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or product damage.
02. Use a dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire.
03. This product is designed to detect the pressure of noncorrosive medium. Do
not use for corrosive medium.
Failure to follow this instruction may result in product damage.
04. Keep the product away from metal chip, dust, and wire residue which flow
into the unit.
Failure to follow this instruction may result in fire or product damage.
Cautions during Use
• Follow instructions in 'Cautions during Use'.
Otherwise, it may cause unexpected accidents.
• 12 - 24 VDCᜡ power supply should be insulated and limited voltage/current or Class 2,
SELV power supply device.
• Use the product, 3 sec after supplying power.
• When using switching mode power supply, frame ground (F.G.) terminal of power
supply should be grounded.
• Wire as short as possible and keep away from high voltage lines or power lines, to
prevent inductive noise.
• This unit may be used in the following environments.
- Indoors (in the environment condition rated in 'Specifications')
- Altitude max 2,000 m
- Pollution degree 3
- Installation category II