- ページ 3

温度コントローラー Gammaflux TTCのPDF 高度なセットアップ/トラブルシューティングをオンラインで閲覧またはダウンロードできます。Gammaflux TTC 4 ページ。

ページを印刷する

Advanced Setup

The TTC International interface is shipped to the

customer so that no setup work is required for

basic operation. Set points in automatic and

manual may be entered and the zone will be

controlled by turning "On" the zone power. Many

customers require advanced features to satisfy

their operation. This page will describe the basics

of "Advanced Setup". Please note that security

levels are not standard. To place security on the

TTC International Interface you must activate

security by selecting your own personalized

security codes.

Advanced Setup Guide – Level 2 Security to Change

Limit (default)

(0)

0 -10 (0)

(1)

0 -10 (0)

(2)

+/ -100ºF / 55ºC (20ºF / 11ºC)

(3)

0- 300 seconds (60)

(4)

-31 to 27 (0)

(5)

0 -1000ºF / 537ºC (20ºF / 11ºC)

(6)

0-1000ºF/537ºC (220ºF/104ºC)

(7)

-31 to 27 (0)

(8)

0 to 54.0 minutes (5)

(9)

0-1000ºF/537ºC (999ºF/537ºC)

(10) 0-1000ºF/537ºC (999ºF/537ºC)

(11) 0-100% (100%)

(12) 0-1000ºF/537ºC (50ºF/28ºC)

(13) 0-1000ºF/537ºC (100ºF/56ºC)

(14) 0 or 1 (0)

(15) 0 to 1000 seconds (0)

(16) 0- 2 (0 = all zones)

(17) 0- 2 (0 = all zones)

(18) 0- 4 (0)

(19) 0 or 1 (0)

(20) 0 or 1 (0)

(21) 0 or 1 (0)

(22) 0 or 1 (0)

(23) - - -

(24) - - -

(25) 0- 999 (none)

(26) 0- 999 (none)

(27) 0- 999 (custom)

(28) 0 (0)

(29) - - -

(30) - - -

(31) - - -

(32) - - -

(33) - - -

(34) - - -

(35) - - -

(36) - - -

(37) 000-999 (level 2)

Explanation (*saved in menu)

Restore mold setup – access advanced setup. 0 – view area. Select menu 1-10. Enter to restore

Save mold setup – access advanced setup. 1 – view area. Select menu 1-10. Enter to save

Boost temperature set point. 2 – view area. Amount of temperature added to automatic set point during a boost

Boost time set point. 3 – view area. The amount of time boost is active

Algorithm set point (view only). View auto tuning selection or manual tuning value.

Temperature deviation alarm set point. Actual temperature activates individual zone alarm at this amount +/- set point

Standby set point (individual). When standby is activated, all automatic zones in the standby group will control to this set point

Control algorithm adjustment (individual). 0 = auto selection. To view actual tuning value select code 4

Manual Selections: 10 to 17 fast tuning with increasing lag. 20 to 27 slow tuning with increasing lag

-1 = very fast tuning; -17 to -10 fast manifold tuning with increasing lag. -27 to -20 very fast tuning with increasing lag

-30 and -31 ultra fast low mass tuning. P = auto selection tune performed (view area)

T/C pinched detection time (individual). 0 = normal (98+% output, 20ºF / 11ºC in 5 minutes). Change alarm timer amount

Critical over temperature alarm. If this temperature is exceeded for 8 seconds, all zones in automatic are turned "Off"

Automatic set point limit. The maximum set point an operator can enter in automatic

Manual set point limit. The maximum set point an operator can enter in manual

Boost limit. The maximum amount of degrees an operator can raise or lower the zone(s) during a boost

Trim limit. The maximum amount of degrees an operator can permanently change the zone(s) during a trim

Enable material protection input. Must see input repeat in time selected or will activate standby group. 0 = "Off"; 1 = "On"

Material protection time. Amount of time from 22-132 VAC/VDC input signal to activate standby group unless signal repeats

Set standby group. Select zone(s) to go into standby when activated by remote input. 0 = all; 1 = display; 2 = store

Set slaved power-up group. Select zone(s) to heat within 20ºF / 11ºC of one another until set point. 0 = all; 1 = display; 2 = store

Power Priority™. 0 = (off). 1-4 = increased smoothing of power output. A = Power Priority™ is active (view area)

Enabled slaved power-up. 0 = "Off"; 1 = "On"

Degree F or C selection. 0 = "degree F"; 1 = "degree C"

Type J or K thermocouple selection. 0 = "type J"; 1 = "type K"

Zone power status on power up. 0 = "all zones turned Off"; 1 = "zones On when shut down last, stay On"

Reserved for future use

Security code level 1. You must be in level 2 to change. Refresh procedure available, call Gammaflux

Security code level 2. You must be in level 2 to change. Refresh procedure available, call Gammaflux

Zone finder (locate zones). Finds new hardware, to activate enter 999. Displays number of zones available in the system

LED test. To activate, enter 0. Turns "On" all LEDs for troubleshooting

Output module software version number (display only), select zone, version displayed

Output module software revision number (display only), select zone, revision displayed

T/C input software version number (display only), select zone, version displayed (16 zones per module)

T/C input software revision number (display only), select zone, revision displayed (16 zones per module)

Data concentrator software version number (display only), select zone, version displayed

Data concentrator software revision number (display only), select zone, revision displayed

Operator panel software version number (display only), version displayed

Operator panel software revision number (display only), revision displayed

Security level indicated. 0 = lockout; 1 = operator; 2 = supervisor; 0 - enter, drops one level

Elevate one security level at a time with your customized code

Setup Number

Scroll Up

Current Value

Scroll Down

Access/Exit

Advanced Setup

Press both select

buttons at the same

time, hold and release.

Selection LED's go

dark in advanced

setup mode.

Set individually by zone