ページを印刷する
SmartGate QuickStart
Read the CD-ROM User Manual carefully to get familiar with all system functions.
Security Precautions
• Do not switch on SmartGate in the vicinity of medical
apparatuses to avoid interference. The minimum distance
of the antenna and pacemakers should be 0.5 m.
• Do not switch on SmartGate aboard a plane.
• Do not switch on SmartGate near petrol stations, chemical
facilities or sites where explosives are used.
• Any mobile telephone use prohibition based on RF energy
radiation applies to SmartGate too.
• SmartGate may disturb the function of TV sets, radio sets
and PCs.
• Warning! SmartGate contains components that can be
swallowed by small children (SIM card, antenna, etc.).
• The voltage value mentioned on the power adapter may
not be exceeded. If you connect SmartGate to another
power supply, make sure that the voltage value is in the
acceptable range.
• When your SmartGate comes to the end of its operational
life, dispose of it in accordance with applicable regulations.
Basic Functions
• The primary purpose of SmartGate is to
transmit voice between a GSM network
and connected telecommunication devices.
• You can
establish
data connections
(GPRS, CSD) and send/receive SMS in
combination with a PC.
• You can send an SMS to a pre-
programmed number using the SMS
sending input.
• Models of SmartGate with fax converter
can
transmit
fax
messages
using
analog fax Group 3 on telephone line.
External Antenna Connection
Screw the antenna into the SMA antenna
connector. Tighten the antenna connector
gently with your hand, never use spanner!
Use antenna with coax cable if the GSM
signal is poor, or in case of interference.
SIM Card Installation
Open
the
SIM
card
holder
on
SmartGate's back side, insert the SIM
card and close the holder properly.
Select the required GSM provider and
SIM
card
services,
such
as
call
forwarding,
call
barring,
preferred
networks, SMS centre, etc. using your
mobile phone before inserting your SIM
card in SmartGate.
A SmartGate delivery contains:
SmartGate
Antenna for direct
connection
Antenna with coax cable
Supply adapter
Telephone cable
PC-connection serial cable
SMS sending input
connector
Dowels
Screws
SW programs and User
Manual on a CD-ROM
QuickStart manual +
mounting pattern
Warranty certificate
Proper Location
• SmartGate is designed for vertical mounting on
suspension holes (use the mounting pattern). This
position is the best for GSM signal reception.
• Install SmartGate with respect to a good GSM signal
strength.
• Place SmartGate out of range of sensitive devices and
human bodies for electromagnetic interference reasons.
• SmartGate is designed for indoor use. Do not place it
near heat sources and on sites exposed to direct solar
radiation. It may not be exposed to rain, flowing water
and moisture. In addition, it may not be exposed to
aggressive gas, acid vapours, solvents, etc.
Telephone Lines Connection
Connect
any
FXO-interface
equipment
telephone set, answering machine, PBX CO line,...) to
FXS interface (Phone icon) on SmartGate. To FXO interface
on SmartGate (crossed out Phone icon) connect FXS-
interface equipment (internal line of PBX). SmartGate is
equipped with CLIP via FSK on FXS interface and so it is
advantageous to connect a terminal that is able to display the
CLI.
Power Supply Connection
SmartGate is powered with 10-16V DC voltage. Where a
source other than the included supply adapter is used, the
voltage range and polarity shown on the SmartGate supply
connector have to be maintained. Do not switch on the power
supply until the antenna is connected to SmartGate to avoid
the GSM module damage.
SIM Card PIN protection
1. Hook off the telephone, you can hear the PIN
tone:
1 pc
2. Enter the PIN using the DTMF and press a
for confirmation. To cancel a wrong PIN hang
1 pc
up the telephone line.
3. If you hear the busy tone in a while (a few
1 pc
seconds), you have entered the PIN correctly.
1 pc
The PIN will be entered automatically upon the
2 pc
next power up.
1 pc
4. If you hear the PIN tone again in a while, you
1 pc
have entered a wrong PIN. Re-enter the PIN.
Phone calls – DialThru gateway
2 pcs
Initial SmartGate behavior is like that:
2 pcs
• Calls from FXS interface are routed to GSM
1 pc
network.
• Incoming calls from GSM rings on FXS
1 pc
interface.
• In case of incoming ringing on FXO interface,
1 pc
both analog interfaces on SmartGate are
interconnected. So ringing is transferred to
FXS interface and FXO-FXS call is enabled.
For advanced calls routing you have to
program
Routing
distributors may preprogram tables for usual
use in your country.
• SmartGate is able to route calls according to
phone number prefix. Calls from FXS interface
can be routed not only to GSM network, but
also to FXO interface. It is necessary to
program FXS routing table for this.
• ME – Mobility Extension is new useful
function on our gateways. If ME is activated
and incoming call rings on FXO interface,
SmartGate routes this call to FXS interface and
simultaneously
network. You can receive the call on analog
(standard
line as well as on your mobile phone.
Phone calls – gateway for PBX internal line
You can switch SmartGate from DialThru
gateway to gateway for PBX internal line by
setting of only one parameter. You can find it on
FXO routing table page.
• Calls from FXO interface are routed to GSM
network.
• If incoming calls from GSM network have to be
routed back to FXO interface, it is moreover
necessary to program the Other CLI's row in
GSM routing table. (If you want SmartGate to
route incoming GSM calls according to CLI, fill
in GSM routing table rows, as you need).
The manufacturer, 2N TELEKOMUNIKACE a.s, hereby declares that the 2N SmartGate equipment is in
compliance with the essential requirements and other relevant provisions of the 1999/5/EC Directive.
The Declaration of Conformity is available on CD-ROM and at website www.2n.cz.
Analogue FAX and Data Connection (optional)
SmartGate with fax converter has ability to
manage fax messages using analogue fax
Group 3 and data connection using analogue
modem connected to telephone line. The fax or
data service must be registered with your GSM
operator.
Outgoing FAX Call and Data Connection
Before destination number dial code *01* for fax
call or *02* for data connection.
Incoming FAX Call and Data connection
It is recommended to activate separate fax
number on your SIM card –multinumbering
scheme. Fax messages and data connection
should be routed to appropriate number.
It is possible to set fax engine in the gateway to
receive the next call as fax or data call or make
this setting permanent - see the manual on CD.
Indication LEDs
Power
supply
tables.
Some
local
GSM
network
establishes
call
to
GSM
Phone
line
• Light is on whenever SmartGate is
on.
• light = registered to GSM
• flashes once in 1s = not registered,
SIM card inserted
• flashes once in 3s = not registered,
SIM card not inserted
• flashes 4 / 8 times quickly = enter
your PIN / PUK
• no light = standby
Orange for FXS interface:
• flashes quickly = line off-hook or
ringing
• light = call FXS – GSM
• flashes once in 3s = data connection
in progress
On FAX models:
• Flashes 2 times then pause = fax
connection in progress; after power
on signalize need of FW upgrade
Green for FXO interface:
• flashes quickly = line off-hook or
ringing
• light = call FXO – GSM
Alternately orange and green:
• quickly = ringing from FXO is
connected to FXS interface
• slowly = call FXS – FXO