- ページ 22

食器洗い機 Indesit IDL 411のPDF 設置および使用マニュアルをオンラインで閲覧またはダウンロードできます。Indesit IDL 411 25 ページ。

ページを印刷する

Installation

Positioning the Appliance

Position the appliance in the desired location. The back

should rest against the wall behind it, and the sides, along

the adjacent cabinets or wall. The dishwasher is equipped

with water supply and drain hoses that can be positioned

to the right or the left to facilitate proper installation.

Levelling the Appliance

Once the appliance is positioned, adjust the feet (screwing

them in or out) to adjust the height of the dishwasher,

making it level. In any case, the appliance should not be

inclined more than 2°.

If the appliance is level, it will help ensure proper perfor-

mance.

This dishwasher model can be built under a single worktop

(please read the relevant instruction sheet).

Anti-flooding protection

Your dishwasher is provided with a special system which

blocks the water supply in the event of leaks inside the

appliance.

Cold Water Connection

This electric household appliance should be connected

to the water mains using the cold water supply hose

provided with the appliance only. Do not use a different

hose. In the event of replacements, use original spare

parts only.

Connect the cold water supply hose to a threaded 3/4

(gas) connector, and making sure that it is fastened tightly

in place. If the water pipes are new or have not been used

for an extended period of time, let the water run to make

sure that the water is clear and free of impurities. If this

precaution is not taken, there is a risk that the water inlet

can get blocked and damage the appliance.

- It is strongly recommended to use a new hose to connect

the dishwasher to the water supply line, and the old hose-

set should not be reused. Asking to specilized shop or

an authorized service technician (see Service).

Hot Water Connection

The water supply to the appliance can also be connected

to the house's hot water line (centralised system, heating

system), as long as it does not exceed a temperature of

60° C.

In this case, the wash cycle time will be shortened by

about 15 minutes and the wash efficiency slightly reduced.

The connection must be made to the hot water line following

the same procedures as those for the connection to the

cold water line.

Drain Hose Connection

Fit the drain pipe into a drain

line with a minimum diameter

of 4 cm or place it over the

sink. Avoid restricting or

bending it. Use the special

plastic elbow provided (see

figure) to position it in the

best possible way. The part

of the pipe marked with the

letter A should be between 40 and 100 cm above the

ground.

The pipe should not be immersed in water.

Attention: The special plastic hose support must be

solidly fastened to the wall to prevent the drain hose

from moving and allowing water to spill outside the drain.

Electrical Connection

After making sure that the voltage and frequency values

for the current in the home correspond to those on the

rating plate (located on the stainless steel inner door of

the appliance) and that the electrical system is sized for

the maximum voltage on the rating plate, insert the plug

into an electrical socket which is earthed properly (the

earthing of the appliance is a safety requirement mandated

by law). If the electrical socket to which the appliance

must be connected is not appropriate for the plug, replace

the plug, rather than using adpators or the like as they

could cause overheating and burns.

Caution:

- Once the appliance has been installed, the electrical

plug and socket should remain accessible.

- If the power supply cable is damaged, it must be

replaced by the manufacturer or its Technical Assistance

Service in order to prevent all potential hazards. (See

Assistance)

- The cable should not be bent or compressed.

- The Company shall not be held responsible for any

incidents that occur if these regulations are not observed.