- ページ 2
自転車アクセサリー Shimano FC-M590-LのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Shimano FC-M590-L 2 ページ。 Deore front chainwheel
ページを印刷する
SI-0093A-002-00
General Safety Information
WARNING
• Be careful not to let the cuffs of your clothes get caught in the chain while riding, otherwise you may fall off the
bicycle.
• Check that the tension of the chain is correct and that the chain is not damaged. If the tension is too weak or
the chain is damaged, the chain should be replaced. If this is not done, the chain may break and cause
serious injury.
• The two left crank arm mounting bolts should be tightened alternately in stages rather than each bolt being
fully tightened all at once. Use a torque wrench to check that the final tightening torques are within the range
of 12 - 14 N·m. Furthermore, after riding approximately 100 km (60 miles), use a torque wrench to re-check
the tightening torques. It is also important to periodically check the tightening torques.
If the tightening torques are too weak or if the mounting bolts are not tightened alternately in stages, the left
crank arm may come off and the bicycle may fall over, and serious injury may occur as a result.
• Check that there are no cracks in the crank arms before riding the bicycle. If there are any cracks, the crank
arm may break and you may fall off the bicycle.
• If the inner cover is not installed correctly, the axle may rust and become damaged, and the bicycle may fall
over and serious injury may occur as a result.
• Obtain and read the service instructions carefully prior to installing the parts. Loose, worn or damaged
parts may cause the bicycle to fall over and serious injury may occur as a result. We strongly recommend only
using genuine Shimano replacement parts.
• Obtain and read the service instructions carefully prior to installing the parts. If adjustments are not carried
out correctly, the chain may come off and this may cause you to fall off the bicycle which could result in
serious injury.
• Read these Technical Service Instructions carefully, and keep them in a safe place for later reference.
Note
• In addition, if pedaling performance does not feel normal, check this once more.
• Before riding the bicycle, check that there is no play or looseness in the connection. Also, be sure to retighten
the crank arms and pedals at periodic intervals.
• If a squeaking noise is heard coming from the bottom bracket axle and the left crank arm connector, apply
grease to the connector and then tighten it to the specified torque.
• Do not wash the bottom bracket with high-pressure jets of water.
• If you feel any looseness in the bearings, the bottom bracket should be replaced.
• If the amount of looseness in the links is so great that adjustment is not possible, you should replace the
derailleur.
• You should periodically wash the chainrings in a neutral detergent and then lubricate them again. In addition,
cleaning the chain with neutral detergent and lubricating it can be an effective way of extending the useful life
of the chainrings and the chain.
• If the chain keeps coming off the chainrings during use, replace the chainrings and the chain.
• When the chain is in the position shown in the illustration, the chain may
contact the front chainrings or front derailleur and generate noise. If the
noise is a problem, shift the chain onto the next-larger rear sprocket or
the one after.
• Apply grease to the left and right adapters before installing them.
• Be sure to read the service instructions for the Front Drive System in
conjunction with these service instructions.
• Parts are not guaranteed against natural wear or deterioration resulting
from normal use.
• For maximum performance we highly recommend Shimano lubricants and maintenance products
• For any questions regarding methods of installation, adjustment, maintenance or operation, please contact a
professional bicycle dealer.
Technical Service Instructions
Front Chainwheel (2-piece crank)
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
Please note: specifications are subject to change for improvement without notice. (English) © Feb. 2009 by Shimano Inc. XBC IZM Printed in Malaysia.
Specifications
Chainwheel
Model number
Chainwheel tooth combination
Bolt circle diameter
Crank arm length
Chain line
Bottom bracket shell width (Thread dimensions)
Applicable bottom bracket
Bottom Bracket
Model number
Applicable front chainwheel
Bottom bracket shell width (Thread dimensions)
Installation of the Front Chainwheel
Follow the procedure in the figure.
1, 2
Use the special tool TL-FC32/36 to install the right adapter
(counterclockwise thread) and the left adapter (clockwise thread).
Tightening torque: 35 - 50 N·m {305 - 435 in. lbs.}
3
Insert the right crank unit.
4
Set section A of the left crank into the axle of the right crank
unit where the groove is wide.
5
Use the TL-FC16 to tighten the cap.
Tightening torque: 0.7 - 1.5 N·m {6 - 13 in. lbs.}
6
Push in the stopper plate and check that the plate pin
is securely in place, and then tighten the bolt of the left
crank arm. (5 mm Allen key)
Note :
Front
chainrings
Rear
I Spacer installation method
sprockets
(1) Check whether the width of the bottom bracket
shell is 68 mm or 73 mm.
(2) Next, install the adapter while referring to the
illustrations below.
< Normal type >
Band Type
68 mm
*
SI-0093A-002
F
A
73 mm
3-77 Oimatsu-cho, Sakai-ku, Sakai-shi, Osaka 590-8577, Japan
*
If using three 2.5 mm spacers with a band type and a bottom bracket shell having a width of 68 mm,
install the three spacers so that there are two on the right and one on the left.
FC-M590 / FC-M591
44-32-22T / 48-36-26T
SM-BB51
SM-BB51
FC-M590 / FC-M591
Each of the bolts should be evenly and equally
tightened to 12 - 14 N·m {106 - 122 in. lbs.}.
< Chain case specifications >
Bracket Type
68 mm
68 mm
F
F
F
BB mount-
B
C
A
type bracket
F
F
F
F
A
A
A
A
73 mm
73 mm
F
A
FC-M532 / FC-M533-K
FC-M542
44-32-22T / 48-36-26T
44-32-22T
104 mm / 64 mm
170 mm, 175 mm
50 mm
68, 73 mm (1.37 X 24 T.P.I.)
SM-BB50
SM-BB50
FC-M543-K / FC-M542 / FC-M533-K / FC-M532
68, 73 mm (1.37 X 24 T.P.I.)
Wide groove
TL-FC32
area
4
5
TL-FC16
6
2
Inner cover
Plate pin
Note :
Set the stopper plate in
the right direction as
Stopper plate
shown in illustration.
Push up
Spacer
F
A
2.5 mm
Band Type
Chaincase Stay Type
68 mm
68 mm
**
F
F
Chaincase stay
B
C
F
F
F
F
F
A
A
C
A
A
73 mm
73 mm
F
F
A
C
**
1.8 mm corresponds to the thickness
of the chain case.
FC-M543-K
44-32-22T / 48-36-26T
1
3
F
F
B
C
1.8 mm
0.7 mm
Bracket Type
F
BB mount-
A
type bracket
F
A