- ページ 4

屋外ライト Acuity Brands Lighting Holophane Wallpack HLWCP2のPDF インストレーション＆メンテナンス・マニュアルをオンラインで閲覧またはダウンロードできます。Acuity Brands Lighting Holophane Wallpack HLWCP2 6 ページ。 Full cutoff led luminaire

ページを印刷する

HOLOPHANE

Figure 3

3" mount

2.2.4 For conduit entry or J-Box mounting, remove the

appropriate threaded plug on the electrical housing

2.2.5 Insert the supply wires or thread conduit through

the hole and secure housing to the wall using fasteners,

not included, that are appropriate for the size and weight

of the luminaire as well as the substrate the luminaire is

being mounted to.

2.2.6 Apply a continuous bead rubber silicon to seal the

back housing to the wall.

2.2.7 Apply a continuous bead rubber silicon to fully seal

any unused conduit entry points.

2.3 Wiring the Luminaire – Standard Luminaire

2.3.1 Using the provided chains and hooks, hang the

heatsink on the electrical housing for temporary support

during wiring.

2.3.2 Check Voltage to ensure the line voltage matches

the voltage range shown in the luminaire description on

the fixture label.

2.3.3 Reconnect any wiring that had been undone when

removing the heatsink from the electrical housing.

2.3.4 Connect the line voltage supply wires to the

luminaire input wires using the pre-installed lever nuts.

2.4 Wiring the Luminaire – Emergency Battery Pack

(EM) Luminaires only

2.4.1 Follow steps 2.3.1 to 2.3.3

2.4.2 Connect the line voltage supply wires to the

luminaire input wires using the pre-installed lever nuts.

For the emergency battery pack, both the switched

(white/red wire from battery) and unswitched

(orange/black wire from battery) lines are run through

surge protection devices. The unswitched line will be

labeled on the surge protection device.

2.4.3 Connect the battery pack inverter (red and white

wires with clear, plastic caps) to enable the battery back-

CAUTION: The emergency battery pack must be

allowed to charge for 24 hours prior to testing operation.

The battery will continuously discharge until it is drained

and will begin charging when the luminaire is energized.

CAUTION: Luminaires with an emergency battery pack

cannot be mounted higher than 10.74 ft. from the ground

Wallpack

LED Luminaire (HLWPC2)

5" mount

4" mount

GR2675

Full Cutoff

in order to comply with UL emergency lighting 1-ft candle

criteria

2.5 Wiring the Luminaire – Two Independent Circuit

(2CI) Luminaires only

2.5.1 Follow steps 2.3.1 to 2.3.3

2.5.2 Connect the line voltage supply wires to the

luminaire input wires using the pre-installed lever nuts.

For the 2CI option, there should be 2 identical drivers

present in the luminaire. The driver that is intended to be

label from the factory. The wire color for the unswitched

line will be variable depending on the performance

package chosen.

2.6 Attaching Heatsink to Electrical Housing (Figure

2.6.1 Bring the heatsink close to the electrical housing

and insert the 4 guiding pins on the heatsink into the 4

guiding holes in of the electrical housing

2.6.2 Making sure not to pinch any wires or chains, slide

the heatsink until it makes contact with the electrical

housing.

2.6.3 Tighten the 6 screws to 20-25 in-lbs. to ensure a

watertight seal and a secure connection of the heatsink

to the electrical housing.

FAILURE TO TIGHTEN HOUSING SCREWS COULD

CAUSE LUMINAIRE TO FALL RESULTING IN

INJURY, DEATH OR SERIOUS PROPERTY DAMAGE.

NE PAS SERRER CORRECTEMENT LA VIS DE

RÉGLAGE PEUT PROVOQUER LA CHUTE DE LA

FIXATION ET CAUSER DES BLESSURES,

PROVOQUER LA MORT OU DE SÉRIEUX

DOMMAGES MATÉRIELS.

Figure 4

Installation and

Maintenance

Manual

WARNING

AVERTISSEMENT

GR2676

IM‐438‐B