- ページ 7

換気フード Whirlpool WVW91336KSのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Whirlpool WVW91336KS 28 ページ。 Wall-mount canopy range hood

ページを印刷する

It is recommended that the vent system be installed before

■

hood is installed.

Before making cutouts, make sure there is proper clearance

■

within the ceiling or wall for exhaust vent.

Check your ceiling height and the hood height maximum

■

before you select your hood.

1. Disconnect power.

2. Determine which venting method to use: roof, wall, or

non-vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto covered

surface.

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the wall where the

canopy hood will be installed (A).

2. Select a mounting height between a minimum of 24"

(61.0 cm) for an electric cooking surface, a minimum of

27" (68.6 cm) for a gas cooking surface, and a suggested

maximum of 36" (91.4 cm) above the range to the bottom of

the hood. Mark a reference line on the wall (C).

3. Tape the template in place by aligning the template

centerline with the centerline marked on the wall (A) and

bottom of template with hood bottom line (C).

DRI LL 2 ( TW O) 3/ 16" PI LOT HOLES THROUGH STUDS OR REAR W ALL SUPPORT

Hor i zont al Li ne

A. Centerline

B. Fastener locations

C. Mounting height reference (hood bottom line)

4. Mark centers of the fastener locations through the template

to the wall.

IMPORTANT: All canopy mounting screws must be installed

into wood where possible. If there is no wood to screw into,

additional wall framing supports may be required, or use the

(4) 10 x 60 mm wall anchors and 5.4 x 75 mm screws.

Remove the template.

5. For wood, drill 3/16" (4.8 mm) pilot holes at all locations

where screws are being installed into wood.

INSTALLATION INSTRUCTIONS

Prepare Location

REAR W ALL

M OUNTI NG TEM PLATE

ALI GN BOTTOM EDGE

W I TH PENCI L LI NE

I NDI CATI NG BOTTOM

OF THE HOOD

I ns t al l at i on Hei ght

For wall anchors, drill 7/16" (10 mm) holes at all locations

where wall anchors are being used.

6. For wood, install (2) 5 x 45 mm mounting screws on the top

two fastener locations. Leave a 1/4" (6.4 mm) gap between

the wall and the back of the screw head to slide range hood

into place.

For wall anchors, install the 10 x 60 mm wall anchors and

install (2) 5.4 x 75 mm screws into the top wall anchors.

Tighten until the wall anchors are secure. Back the screws

out 1/4" (6.4 mm).

1⁄4"

(6.4 mm)

Vent Cover Bracket Installation

Attach vent cover bracket to wall flush to the ceiling using (2)

5 x 45 mm screws. Use the optional wall anchors if needed.

A. Ceiling

B. Wall

C. Centerline

Complete Preparation

1. Determine and make all necessary cuts in the wall for the

vent system. Install the vent system before installing the

hood. See "Venting Requirements" section.

2. Determine the required height for the home power supply

cable and drill a 1¼" (3.2 cm) hole at this location.

3. Run the home power supply cable according to the National

Electrical Code or CSA Standards and local codes and

ordinances. There must be enough 1/2" (1.3 cm) conduit and

wires from the fused disconnect (or circuit breaker) box to

make the connection in the hood's electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4. Use caulk to seal all openings.