- ページ 28
プリンター Xerox Versant 80 PressのPDF 顧客期待＆インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Xerox Versant 80 Press 48 ページ。 Entry production color presses
Xerox Versant 80 Press にも： 安全マニュアル (26 ページ), セキュリティ・マニュアル (45 ページ)
ページを印刷する
Detailed Specifications
2-Knife Trimmer Module
The 2-Knife Trimmer is an optional finishing device that provides full-bleed trim for square fold booklets.
IMPORTANT:
It is only available with the Booklet Maker Finisher with the SquareFold Trimmer; it is not available with any other finishing device.
For information related to the 2-Knife Trimmer Module, refer to Module Dimensions for Optional Devices and Electrical Requirements for Optional Devices.
2-Knife Trimmer Specifications
2-Knife Trimmer Limitations
Third-Party Finishing Options
Third-Party Finishing devices that can be connected to the Standard Finisher Plus include:
Plockmatic Pro 55/50 Booklet Maker
Specifications and expectations for these devices are available in a Solutions Planning Guide which is available from your Xerox sales representative or analyst. For
Xerox personnel, information may be found at http://www.smartcentre.xerox.com/Portal/.
Media and Substrate
Media Selection Guidelines and Media Support
Media Type
Uncoated Paper
Coated Paper
Every effort has been made to ensure that the Press supports a broad range of media. Using only Xerox-recommended media helps maximize reliability
and paper-handling performance. Furthermore, use of the Centerline papers is recommended to help ensure that you receive the best image quality from
your Press.
Typically, heavy weight papers exhibit increased variability of formation and surface smoothness, which may result in degraded image quality.
Paper from all trays is printed topside first. It is recommended that Xerox branded paper be loaded with ream wrapper seam-side up.
Manufacturers of coated stock do not recommend use of their media when the ambient relative humidity exceeds 60%. Relative humidity greater than
40% may increase the misfeed rate from Trays 1, 2, 3 and 5 (Bypass).
All paper stretches to a certain extent during printing. The amount of stretch is dependent on paper type and environmental conditions. Stretch is most
noticeable on coated stocks. This stretch can affect front-to-back image registration. Use the Alignment Profiles feature with the SIQA tool to minimize
this effect.
Image registration, image quality (for example white spots), and machine reliability can be adversely affected when custom-cut paper is inaccurately cut,
is of poor quality, or loose paper fibers are present on the cut edges.
Image registration, image quality (for example white spots), jam frequency and machine reliability can be adversely affected when punched or drilled
paper is of poor quality and/or loose hole plugs are present in the ream.
For further information and recommendations regarding media testing, selections, and handling, refer to the Recommended Media List (RML) available
from your Xerox representative or downloaded at www.xerox.com.
Press Output and Other Equipment
The Press output (prints) should not be run through the printing path of Nuvera® or DocuTech® Production Publishing systems. However, the prints can
be used with the Interposer module.
Nuvera, DocuTech, and other technology output, including preprinted offset shells, should not be run though the printing path of a Versant® 80 Press.
If you plan to run the Press output through other equipment, including finishing devices such as a coater or laminator, it is recommended you test the
application before committing to the job. Many factors impact the success of running the Press output in other equipment.
Duplex (2-Sided Prints)
Automatic duplex printing can be performed on recommended media up to 13 x 19 in (SRA3 320 x 450 mm/maximum 320 x 482 mm) from 52-300 gsm.
Manual duplex can also be performed on recommended media up to 13 x 19 in (SRA3 320 x 450 mm/maximum 320 x 482 mm) from Tray 5 (Bypass).
As with any printer or copier, duplex performance may not match the performance for single-sided printing or copying. Paper jam rates may be higher
than the rate you will experience for the same throughput material in single-sided mode.
In order to reduce paper jam frequency when duplex printing on stocks heavier than 220 gsm (80 lb. Cover), paper grain should be perpendicular to the
print process direction (i.e. Short Grain).
Customer Expectation and Installation Guide
Feature
Specification (with centerline paper)
Paper Types and Weights
Coated and Uncoated
Paper weights: 18 lb. Bond – - 110 lb. Cover (64 gsm – 300 gsm)
Cover weights: 45lb Cover – 110 lb Cover (120 gsm – 300 gsm)
Paper Size
Minimum: 8.5 x 11 in. SEF (216 mm x 279 mm)
Maximum: 13 x 18 in. SEF (330 mm x 457 mm)
Trim Capacity
5—20 sheet booklet at 24 lb (90 gsm)
5—20 sheet booklet at 20 lb (80 gsm)
Trim Dimensions
1/16" – 1 3/8" (2 – 35 mm) at 0.1 mm increments
When clearing a fault on the 2-Knife Trimmer, the SquareFold Trimmer will also need to be reset. The SquareFold
Trimmer can be reset by opening and closing the waste bin.
Always empty the waste bin for both the 2-Knife Trimmer and SquareFold Trimmer at the same time.
The 2-Knife Trimmer can handle cover paper as low as 60 gsm, for best results, 120 gsm to 300 gsm is recommended.
Versant® 80 Press Centerline Paper
North America - Xerox Color Xpressions Plus (90 gsm/24 lb.)
Europe Colotech+ (90 gsm/24 lb.)
North America Xerox Digital Color Elite Gloss 80 lb. Text (120 gsm)
Europe Xerox Digital Color Elite Gloss 80 lb. Text (120 gsm)
Xerox Confidential
Xerox
Versant® 80 Press
®
23